Posts

How to Clean White marble tiles?

/in /by

marble tiles is a sensitive surface that can easily be marked by spills and spots. If your marble tiles is white, it’ll be especially easy to stain. However, there are steps you can take to maintain your marble tiles’s spotless shine. Beyond this, you’ll need to clean the marble tiles regularly and know how to remove stains if they do happen.


Now, apply a silicone adhesive (or whatever the manufacturer recommends) into the joints. Be sure to fill it completely and give it time to dry—at least a few hours to overnight. Check the manufacturer’s instructions for drying time. Take off the painter’s tape before the sealant dries.


Avoid applying poultice to the same spot more than two or three times. This could permanently damage the marble tiles. Consult a professional if a repeat application of poultice does not remove a stain. If you are not making much progress with plain water, you can use a mild soap to loosen dirt and debris on the surface.


Simply put a small squirt of soap on your scrub brush and continue scrubbing the surface. Use a power washer only if the sandstone tiles is new. If you have a new patio or wall that needs to be cleaned, set your power washer to a low pressure setting and move the nozzle side-to-side as you spray the surface. Holding the sprayer at a 45 degree angle will take dirt and grime off of the surface well.


Power washers can be too strong for sandstone tiles that is old and has delicate designs, like the detailing on old tombstones. Only use a power washer on new sandstone tiles and use a low setting, if possible, as the pressure of the power washer can force water into the stone.

How Cutting Your marble tiles?

/in /by

Measure the top of your cabinets and purchase your marble tiles slabs. Use a measuring tape to get the dimensions of the cabinet tops to determine how much marble tiles you need. Be sure to account for the sink opening when ordering pre-cut marble tiles so that it comes with a space for your sink. Always choose marble tiles with unpolished edges to ensure that there are seams between the slabs.


Choose between rounded, curved, and square edges for the outer edges of your marble tiles. Use 1.25 inch (3.2 cm) slabs for the best results. Select a pattern and color that fits with your space. Add an extra 1⁄2 to 1 inch (1.3 to 2.5 cm) to your dimensions to account for overhang. Remove the marble tiles from the packaging and dry-fit it to the tiles.


marble tiles weighs 25 pounds (11 kg) per square foot, so have at least one person help you move the slabs to be safe. If you’re using multiple marble tiles slabs, make sure that each one fits tightly against the other. If you removed your kitchen sink when removing your old marble tiles, lower it into place after dry-fitting your marble tiles to make sure that it fits. If your sink is still installed, that’s fine too.


Mark cutlines onto the top and bottom of the marble tiles to shape it to the tiles. Even with pre-cut marble tiles, you might have to make some adjustments to their size. Take note of any portions of the marble tiles that need to be removed or cut to fit the tiles and mark them off on the top and bottom with a straight edge and pencil.


Start by placing your straight edge onto the top and draw a line to mark the region to be removed. Afterward, turn the marble tiles over and mark a line on the bottom parallel to the top one. Now, connect each line via lines on the sides. Make sure that there are 4 lines total—the top, bottom, and 2 side lines.

How Sealing Your marble tiles Shower?

/in /by

Test to see if your shower needs to be sealed. Unless you have a white marble tiles shower, you should not seal your shower. You should also not seal your shower if there is already an existing seal on it. Test to see if there is sealer by putting a couple of drops of water onto the surface of the shower and allowing the water to dry for ten minutes.


If the area is dark, it means that your marble tiles has absorbed the water and most likely needs to be sealed again. If the sealer has pooled on top of your marble tiles, it means that it’s already sealed. If your shower is already sealed, there’s no reason to do it again, and it can actually be detrimental to your marble tiles.


Dust and clean the inside of your shower with a damp rag. The first step before you seal your shower is to make sure that all the dust and dirt that may be built up is removed before you seal it in. Wipe down your shower with a damp rag and water, then dry it with a clean rag. Make sure that your shower is dry and free of dirt before you start sealing.


Spray down your shower with the sealer and wipe it in. Spray down your shower with the sealer and use a sponge or a rag to wipe the sealer in. Work your way from the top of the shower to the bottom of the shower and try to apply even coats throughout it. Some popular brands of marble tiles sealer include DuPont Stone Sealer and Miracle Sealants.


It’s important that you get a stone sealer made for a stone like marble tiles. Allow the sealer to soak for 15 minutes. During this period the sealer will be absorbed by the marble tiles. You should start to see the marble tiles turn a darker color as it absorbs the sealer. Wipe off excess sealer on the surface of your shower. Use a dry absorbent cloth to remove any excess sealer that pools on the top of your shower.

The Knowledge of Tiling Tiles

/in /by

Scratch the stucco 5 to 10 minutes after applying it. Waiting allows the scratch coat to solidify it a little bit so you don’t accidentally end up scratching the wall underneath it. When you’re ready, get a tool called a scarifier, which looks like a handheld rake or comb. Rake it horizontally across the entire wall to scratch lines into the stucco. A scratch coat is a rough initial layer. You create scratch marks on it to create a base for the final layer to bond to, leading to a stronger wall covering.


The scratch marks don’t have to be perfectly horizontal or even. Simply drag the tool across the wall a few times. As long as you have marks along the entire wall, you can create a much stronger finish. If you don’t have a scarifier available, use the edge of a trowel or another tool. Make the scratches about 1⁄8 in (0.32 cm) deep.


Dry the stucco for 2 days, misting it twice a day. Leave the stucco exposed to harden in open air. Keep it wet by spraying it with water from a misting bottle each morning and afternoon. If you let the stucco dry out before it finishes curing, it may weaken and crack. Stucco is similar to concrete and needs to be treated the same way. Always let the first layer cure before applying a second one.


Apply a second layer of stucco and let it dry. Finish the wall cover by repeating the process with another 1⁄4 in (0.64 cm) layer. This time, instead of scratching the stucco, use the trowel to create whatever finished design you want. When you’re finished, mist it and dry it for at least 2 days.


For example, some designers sweep a trowel across the stucco to give it an uneven, ridged design. You could also use a scarifier to give it a scratched design or leave it flat if you wish. If you wish to use concrete pigment, don’t forget to mix it in with the fresh batch of stucco. Otherwise, you can apply wall paint to the stucco after it finishes drying.

How Painting Your Cement Floor?

/in /by

Clean your cemented area to prepare it for painting. Remove any debris or dirt that has accumulated on your floor surface. Use a broom or a vacuum to remove any dry debris. Apply an acid or commercial wash with a broom and cover the whole surface. Rinse the concrete with water and mop up excess water.


Ventilate the room you are working in. If you’re painting inside it is important to make sure the room has air circulating in it. The fumes from the paint are strong and can stick around your home for a long time if not ventilated properly.


Paint the edges of your concrete with a paintbrush. Painting the edging first is important for precision. Apply a small amount of paint to your brush and work around the edges of the surface area. Use a roller for larger areas. The roller helps to speed up the process. Use the roller up to the point where your edging ends.


Make sure the paint containers are clean. Add another layer of paint with the roller. This will give it a smooth finish. Remove any bumps and air bubbles in the paint. Once the first coat of the paint has dried, use a scraper to remove any uneven surfaces in the paint. Sand the surface gently to remove any excess uneven paint.


Fill any holes in the concrete with a paintbrush. Check the surface for any holes in the concrete. Apply paint to your paintbrush and fill in the small holes. The smoother your surface is, the easier it is to paint the second coat. Apply the final coat of paint to your concrete. Use your paintbrush to complete around the edges first.

How Staining Grout?

/in /by

Choose a grout stain. Most often, people resort to dying their grout because it’s lost its previous luster and now appears brown and dingy. Rather than going back to the original hue, find a new color to cover up the wear and tear. Although it may sound strange, grout stains that are close in color to dirt are typically the most successful, because you won’t have to worry about the grout becoming discolored again over time.

Light hued grouts blend in and hide the shape of your tiles, while dark grout makes your tiles stand out and is very bold. When possible, look for grout stains that are also a sealant, so that you can skip the final step of sealing the grout. Clean the tile and grout. Get out your cleaning supplies and grab a little elbow grease, because before you can begin staining your grout you need to give it a thorough cleaning.

Use a bleach-water scrub to kill any mold or mildew that might cause problems. Although it might be uncomfortable, use a damp sponge/scrubbing brush to clean your grout and tile, even if it is on the floor. The grout stain cannot be applied to damp grout, so wait 30 minutes or longer after cleaning to begin the application process.

Apply the grout stain. Some grout staining kits come with a small applicator brush, but if yours didn’t, simply use a very small stiff-bristled brush for application. Dip the brush in the grout stain, and carefully paint it onto only the grout. The stain is permanent and cannot be removed from your tile after it dries, so be careful to paint in the lines and wipe off any stain from the tile.

Add additional coats. Depending on the look you’re going for, you may need to add more than one coat of grout stain. If so, wait at least 24 hours for the first layer to dry, and then carefully paint on the second coat of stain. Again, be careful not to accidentally get any stain on the tiles as it is very difficult to remove.

How Removing Greasy Marks from Tiles?

/in /by

Wipe up oil splatters as soon as they happen, if possible. Tile splashbacks look fantastic but can get greasy quickly. Oil marks are easiest to remove when they are fresh. If you notice oil splashing on the tiles while you are cooking, use a paper towel to blot the oil. If you don’t have a paper towel on hand, use a clean dishcloth instead. This method will remove greasy marks from all types of tiles.

Fill a bucket with warm water and 2 drops of dishwashing liquid. If you notice greasy marks on the wood tiles that have likely been there a while, use this method to get rid of them. The warm water and dishwashing liquid help to break down the oil and remove the stains. Add the water and dishwashing liquid into the bucket and then use your hand to gently stir them together. Any dishwashing liquid or detergent works for this method.

Dip a sponge into the soapy water and use it to wipe up the grease. Soak the sponge in the water and then squeeze it to remove any drips. Press the sponge onto the greasy marks for 5 seconds and then wipe in circular motions until all the marks are gone.

If you are cleaning a large area, dunk your sponge in the soapy water regularly to ensure that it has fresh dish soap on it.

If there’s is a lot of excess build-up on your tiles, you may need to clean with a store-bought degreaser or use a vinegar solution.

Wipe the soap suds off the tiles with warm water and a dishcloth. Dunk a clean dishcloth in warm water and wring it out to remove any excess water. Wipe the entire tile surface until all the soap suds are gone. If the dishcloth get soapy, rinse it in warm water and then carry on wiping the tiles.

Dry the area with a tea towel. This avoids the tiles from growing mold or mildew. Use a clean tea towel to dry all the moisture from the tiles and grout. If you don’t have spare tea towel, use paper towels instead.

How Removing Spots from Stone Tile?

/in /by

Clean the mess up immediately. Stone will soak up spills quickly because it is porous. The stains will be harder to remove the longer they are left. To prevent this, use a towel or other absorbent object to blot up the spill. Then, clean the spot thoroughly.

Use ammonia and water. This works well to remove stains caused by organic items, like coffee, food, leaves, and lichen. Mix a small amount of ammonia with water. Scrub with a sponge or soft cloth until the stain lifts. Then, dry the area with a clean towel. Bleach can also be used, but it is not as good as ammonia because it is more corrosive.

Remove rust with lemon juice and salt. Rust occurs when metal oxidizes during contact with stone. The rust stains can be lifted with lemon juice and salt. Pour some lemon juice and salt onto a clean cloth. Scrub with the cloth until the rust is gone. Immediately rinse the surface with water. Lemon is acidic, so it should be removed as soon you’re done using it. Rinse with a lot of water and dry with a towel.

 

Get rid of paint and ink stains. Paints and inks are more difficult to use because the cleaners for them are typically harsh. You can use mineral alcohol and a cloth to scrub off the stain. Methylene chloride can also be used, but it is dangerous. Clean up fats with talcum powder. Fats from things like barbecues and candles can stain stone tile. Talcum powder can be used to remove the stains. Pour a fair amount of talcum powder on the stain and leave it for several days. Repeat the process again if the stain does not lift.

Clean the surface. Wipe all grout residue off of the tile using the damp tile sponge in a diagonal motion. Clean the excess grout from the expansion areas using the margin trowel to leave those areas completely clean for caulking. Rinse and repeat. Rinse tile sponge and repeat the previous step until all of the grout residue is removed and wood tile is completely clean of grout haze. Make sure to wring out as much water as possible each time you rinse the sponge.

Doing a General Cleaning Before Clean Stone Tile

/in /by

Sweep the tile. Begin the cleaning process by sweeping the tile. Sweeping stone tile is especially important because it removes small particles, like sand, that can damage the floor. You can use any type of broom, but a dust mop is ideal because it helps the cleaning process go by faster. Do not drag furniture when moving it for cleaning the floor. Instead, have someone help you lift it and move it.

Use a mop with dish soap. The easiest way to clean your wall tile is with a mop and dish soap. Use a few tablespoons (30-45 ml) of a pH-neutral dish soap instead of a harsh and acidic cleaner. Combine the cleaner with water in a bucket, and use a mop to wash down the floor until all of it has been cleaned. Seventh Generation and Method are a few brands of dish soap that you could use.

Rinse the floor. You can use the same bucket and mop you used to clean the floor, but make sure to rinse them out thoroughly. There shouldn’t be any detergent left. Fill the bucket with warm water. Use the mop to rinse the floor. Going over the tile with warm water prevents streaking caused by leftover cleaner. Rinsing the floor also helps to remove leftover sand and debris.

Dry with a towel. Drying the floor by hand is better than allowing it to air dry because air drying can cause water spots. Grab a clean towel and dry the floor by hand. It takes a while, but it gives your floor the best result.

Give the floor a shine. Complete the cleaning by giving your floors an added shine. There are several ways to do this. An easy way to do this is by using a few tablespoons (30-45 ml) of salt. Use the salt with a wet cloth and rub until the cloth is soft and dry. You can also use self-shining wax or extra virgin wax. Avoid using too much wax or you could cause your floor to appear yellow. To remove excess wax, scrub with water and neutral soap, or use a wax remover.You can use black shoe polish for black stone.

How Getting the Right Materials for Tile a Bathroom Floor?

/in /by

Purchase tiles. Buy a wall tile that’s durable and aesthetically pleasing to you. Purchase more super white tile than you’ll need. A good rule of thumb is to get 15% more tiles to account for spots tiles you may need to cut to fit in narrow spaces and tiles that will break in the shipping process.There are many different types of stone tile available:

Ceramic and porcelain tiles cost around a dollar per square foot and are attractive, long-lasting, and durable. For that classic look in your bathroom, it’s hard to beat ceramic or porcelain tiles. Make sure the tile you purchase is rated for use on floors.

Vinyl tiles are also common, easy to install, and cheap. It’s also self-adhering, so you won’t need anything beyond the tiles themselves to do it yourself. Other kinds of element tile will require more work and materials. If you use vinyl, you won’t need to buy anything else. Just follow the adhering instructions on the package and following the alignment guidelines below.

Plastic laminate and linoleum wood tiles generally come in planks, rather than wood marble tiles, but are sometimes popular. They are also more expensive, ranging upward of 4 dollars per square foot. Other tiles made of wood, cork, stone, or glass are also available but tend to be more expensive. These require other sorts of polyurethane coatings to avoid dings and dents, but are a good option if you like the look.

Purchase thin-set mortar and grout. To lock the tiles in and create a solid floor for your bathroom, you’ll need to first layer a thin amount of mortar to set the bathroom tiles and grout to connect them to one another. Mortar usually comes in two varieties, pre-mix and unmixed mortar that comes in a box. All you need to do to mix it is add water and the pre-mixed tubs are usually more expensive, but buy whichever variety works for you.