The choice of floor tiles in family decoration is a big study

/in /by

Floor tile is a large proportion of decoration, and also the largest display area in home decoration. It is the background of style. Understanding the knowledge of these tiles can better communicate with designers and make the most satisfactory home style.

From the material,best floor tiles wear-resistant, waterproof, moisture-proof features not only meet the living room, kitchen, toilet, tread on wear and water frequent requirements, but also can show a good taste of the home, so the general decoration can not be paved with bath floor tiles. From the decoration style, whether you are Chinese, European style, American style, or modern simplicity, floor laying, wall decoration, more floor tiles are indispensable.

Flooring tile matching principle: single tone, the pursuit of unity, small comparison, focusing on practicality. The most important thing is the style that you like. If the living room is well lit (facing the South and long sunshine time), it is suitable for using dark colors and cold tonal subway floor tiles. If it is bright, it will make the room brightness too high, no matter it is beautiful or visual health is not desirable. If the living room is not well lit (sunshine time is in the afternoon or light time is short), it is suitable to adjust with bright colors and warm tones.

We should not blindly pursue the use of large-area ceramic tile flooring. We should tailor them to 40sqm. The following specifications are recommended to be use ceramic floor tiles of 600 x 600mm. Rooms above 40sqm use ceramic floor of 800 x 800mm specifications. The long hall uses the stripe texture floor tile design, the square living room uses the miscellaneous texture floor tile. Texture plays an important role in improving the overall effect of living room. The selection is not only considering personal hobbies, but also paying attention to space collocation.

The home’s overall style and furnishings should be harmonious and unified. In contrast color processing, visual transition is necessary. When laying the floor tiles in kitchen, we must consider the brightness of floor tiles in addition to color. The specific requirements are: the floor tiles same as the wall, or slightly lower than the wall.

The sofa uses the rice white, matches with the black tea table, matches the gray floor tiles, the three forms the very good black-and-white ash transition, from the vision makes the person tight nerve to get soothing. The main body of the TV background wall is “gray black” variegated brick, matching white gray side walls, which is simple and fashionable. In order to reduce the visual fatigue caused by the symmetry of the structure of the background wall, the green planting is collocated on both sides, and the coordination between the design elements is increased, and the whole background wall is simple, simple and simple.

The floor tiles of soft sofa area are replaced with brightly colored small size tiles, making color matching. This design eliminates the monotony of large area of grey floor tiles. The black edge, the white and dark red ceramic kitchen floor tile area and the white sofa, the black tea table hue harmonious, very good highlights each element’s texture.

The hanging ceiling of the living room does not use the chandelier, nor does it hang the task objects, maximizing the living room elements, leaving enough spacious space to meet the people’s demand for space instincts. The open kitchen is more in line with the modern style design requirements. Compared with the enclosed kitchen, the open kitchen makes the space more spacious on the whole space.

The study is a public area for a family. It is spacious and has a wide view. It is convenient to take books and take back books. The bookshelves depend on the wall as a whole, and different books are classified by interlaced cells. Desk is opposite to window, reasonable use natural light, also facilitate long time read a Book overlooking, alleviate eye fatigue. The desk shelf is bright white, and the stool is dark with a simple style to maximize the release of space. From the overall perspective, the living room, kitchen, each structure lines smooth, bright and coordinated. It gives a feeling of refreshness. The whole hue of the bedroom is warm and soft. The design of bed, lamp, sofa and wardrobe can make good use of bedroom space and highlight the unique temperament and refined taste of the room owner.

How to choose tiles for home decoration?

/in /by

Tile is one of the most important materials in our family decoration. It can be used on the floor and wall. Some of them are also used in the kitchen stove. Therefore, the selection and matching of tiles can affect the effect of the whole decoration. It even affects people’s daily life. Therefore, for tiles to be selected, we first need to know the tiles from the following points.

Polished tiles are one of the most commonly used tiles. Because the surface of the tiles (3-4mm thickness of the fabric layer) is polished, it has the characteristics of bright, high hardness, wear resistance and scratch resistance. However, they are usually not tolerant of dirt, and are commonly used in public areas such as living rooms and restaurants.

The polished glazed tile is painted on the surface of the embryo body (porcelain clay and Tao Tu) with a thickness of about 0.1mm-0.2mm thick. It can be classified into full polished tile and semi glazed tiles. Full polished glazed tiles are flat, smooth, and bright. The semi polished tiles are concave and convex, and the convex areas are glazed, while the concave ones are not glazed. Its advantages are rich in color, rich in texture, and resistant to dirt, but the abrasion resistance is not strong. In addition to the kitchen, bathroom, balcony, other places are applicable.

Polished tiles are actually one of full body polished tiles. As the name suggests, the whole body is the same color and material as the bottom. If the surface is polished, it is a polished tile. The full body tile has the advantages of good wear resistance, which is often used in indoor and outdoor walls and floors. glazed rustic tile belongs to glazed tile, glaze on the surface of porcelain tile, deliberately making an old antique effect. For example, the year’s ring, the history of vicissitudes and so on, the glazed rustic tile has the advantages of anti slip, and often used in the kitchen, toilet, balcony, of course, can also be used in the guest restaurant, bedroom and so on.

The first impression of wall tile is that its size is small, smooth and bright, and often used on walls. Besides, what we need to know is that it is different from other tiles. The first is the thickness of the wall tile, the thickness of the wall tiles should be thin. The second is that the location used is different, the wall tile is used on the wall, and the tile can be used on the wall and the ground. The third manifestation is that the service life is different, the wall tiles should be short, and the tiles should be long. The fourth is that the water absorption rate is different, and the water absorption rate of the wall tiles is much higher. Therefore, it is important to note that when wall tiles are used, tiles must be water soaked, otherwise it will absorb the moisture of cement and cause problems such as warping and shedding.

Mosaic tiles include ceramic and glass. Glass mosaic tiles are a piece of tile made of small pieces of tile, so its color and style are rich and can create a warm family atmosphere, which can show the owner’s personality and taste well. And as long as you want to get the result, it can make an effect. In addition, it can be widely used in many places, and can also be used as a cross stone, a background wall, etc.

Microcrystalline stone tile is a new type of building material. The main method is to compounded glass ceramics on vitrified stone. With a strong gloss and permeability, the effect is also more grade, luxury, and the price is more expensive, so it is often used in the TV background wall.

Besides, there are other tiles, such as the wood tile, which we often used, on the surface of our traditional tiles, by a certain process to make its surface with a natural pattern of wood tiles. According to own needs, you can choose tiles suitable for your own homes.

Is there a bad quality of tile with tiles color difference?

/in /by

In nineteenth Century, the French great writer of the Grand Master once said “Russia is crazy about France, and everything imitates France, but because they are too far away, they are always imitating France a century ago.” This sentence seems arrogant, but it did tell a European reality at that time: The whole of Europe is following France in the first place. In fact, this is not only history, but also reality. We have to admit that modern architecture originated in Europe. Europeans are in front of the people of the world in terms of design concepts and decorative styles. To take ceramic tiles, when Europeans are crazy about and pursue the “tiles color difference” of tile, there are still many users in China who are troubled by the “tiles color difference” of tiles.


In recent years, the most advanced tile design country in Italy is very popular with a very artistic design method, known as “return to nature”. What the designer seeks is to completely restore the rich changes of natural color. Just like the two leaves in nature, there are no identical two stones. The most unique charm of nature lies in its richness and diversity. Therefore, the so-called “chromatic aberration” of tiles is actually a presentation of a set of design logic and ideas, and also represents a popular trend of decorative materials.


Leonardo Vinci’s International Airport in Rome, the eternal city, realized the sense of hierarchy and rich aesthetic feeling by using natural chromatic aberration. We often see the United Nations lecture table on television, the entire background wall also used the “floor tiles color difference” approach. Many important regions of European countries that accumulate art and civilization use the transition of color and texture of materials to make the best use of space. Color similar but different tiles, showing a rich sense of hierarchy, The more you look, the more you look more durable


Everything in the world is the same, created by man, and naturally formed by differentiation. How does this “imitation of nature” come true? BARANA tiles use the most advanced technology “Colour Definition System”.This is an innovative digital printing system, which is a very important technology to show the effect of tiles design. Colour Definition System can also make perfect combination of glaze and solid ceramic material on the surface of ceramic materials to achieve the uniqueness of each tiles. In designing the surface effects of each product, BARANA tiles technicians need to carefully study the color reaction of each glaze and porcelain during the firing process and take into account the effect of raw materials and sintering temperature on the color reaction. After the paving, the overall harmony and unity, natural transition and better space effect will be achieved.


The transition of BARANA tiles color texture is divided into four levels. V1 level is pure color, no color gradient effect. The level of gradation increases continuously at every level at the back. Even the same tile can create different space effects, and truly achieve exclusive “private custom tiles”. This magic “color difference” tiles, especially in the laying of stone tiles and wood tiles, has a very amazing effect. Perfect restoration of the most pure sense of nature, full of natural spirit. Compared with the monotony of single color, the color of this change is not easy to cause dull resemble ness. Each tile is similar and different, which truly shows the artistic standard of design.

When the colored tiles went into the kitchen, the beauty burst

/in /by

The color tiles are like a hasty traveler in the history of the river, and perhaps you still exist in the movie scenes of the 30s and 40s as the background of the last century. It bloomed in a special era, and gradually disappeared with the changes of the times. Be the regrettable and forgetting after the flourishing.


The beauty of colourful tiles can be very publicized, and it can also be very introverted. It is an unavoidable surprise to make pure and extensive representations. Mixed with wood tiles, creating a quiet and smart space, as a background wall, makes the whole space more colorful. Each type of colourful tile has unique texture and shape, making the visual focus of space easy. On the small ceramic tile, the colorful splendor color, the decoration prominent pattern, lets the family change the literature and art fan for a second.


The walls of the kitchen are almost covered with tiles, which are generally monotonous. Mainly based on practicability, neglecting the effect of decoration, so there are not many characteristics. If the entire wall is a single color tile decoration, it is inevitable that some boring, let people visual fatigue. If you use decorative tiles to form a visual contrast with other monochromatic tiles, you can easily create visual focus.
The laying of floor tiles can not only lay the tone for the design of the whole space, but also give play to the unique atmosphere of the individual. It can be used for large area surface laying as well as partial use, with the effect of dividing space. It is even possible to extend the floor tiles to the wall boldly, causing strong visual impact to leave a bright impression on people.


Porch, living room, restaurant or other areas, you can use colorful tiles very well. It looks like a carpet, but it’s easier to clean than a carpet. The charming display of the tone makes the space become smart instantly. If you worry about the use of tiles in large areas, it will make the space more messy and dizzy. You may choose to mix and match with other types of tiles. Whether elegant retro style or modern fashion, all kinds of unique texture of small colourful tiles will break the rigid space, so that the whole family does seem to have a lasting appeal. Local application of colourful tiles can become the finishing touch of space. Because of its own space, you can choose a very colorful pattern tiles, which can attract people’s attention. The pattern that captures the eyeball is the greatest feature. Small area, stealth colorful tiles decoration scheme, the exquisite details of the kitchen to the utmost extent, often can achieve amazing effect.


The floral colourful tiles are brightly coloured and have many patterns. They are very attractive in the decoration style. The coloured tiles and plain tiles can be used together to make the space more decorative. Using it as the decorative tile material of the theme wall of the bathroom, it can enhance the overall mood of the bathroom and make the space level more three-dimensional. Colourful floor tiles are similar to ordinary carpet, but they are easy clean than carpet. You will find that the colors patterns tiles of each tile have artistic expression.

What are the problems that need to be paid attention to in the process of tile paving?

/in /by

Do not know what is the reason, many people like to mix the ceramic tile and cement, perhaps because the ceramic tile is more expensive, but the ordinary cement tiles mortar is worried about the sticky, so the ceramic tile is added to the cement mortar and stirred in the mortar. Many people think that ceramic tile glue is almost the same as cement, so mixing it together is no problem. Actually, the ceramic tile glue has its own formula, but when the ceramic tile designs glue and cement sand mix together, the performance of the ceramic tile glue is greatly reduced. If cement mortar has better water retention and better placement, it is recommended to add cement paste to the cement.

Ceramic tiles shop can not be perfect each batch, there will always be a variety of problems, it is suggested that in the process of paving, find problems in time to remind the business of quality or color difference and other problems, timely consultation and solution. It is suggested that the owner inform the constructor before construction: if there are any problems found in the construction, we should timely feedback, so that we can deal with them in time and avoid many problems. In the process of paving, it is found that the tiles have problems, such as the size specification, the ceramic tile price and so on, and the construction should be taken out as far as possible. It can cut small pieces and splice into mosaic use.

Because of the cause of heat expansion and contraction, the ceramic floor tile does not leave the seam, it affects the service life of the tile, and does not leave the seam. The tile will squeeze each other, causing the problems of the glaze crack, the arch, the empty drum, the falling off and so on. Therefore, whether the tiles are plaster or the “seamless tiles” currently mentioned in the market, both of them need to be sewn. The specific width of the stitch should be communicated with the owner before the tile is padded. In order to be more intuitive, the owner can see how good the stitch is when it is decorated.

In the course of laying, tiles are unavoidable to be machined, and when corner paving is applied, they should also be chamfered and collaged. In the collage of Yang Jiao, be careful when chamfering, and try not to damage the glaze. It is best to let merchants or owners get a large processing plant cut. If you are in a hurry, we recommend using some portable electric cutting machines.

This problem is often ignored. When tiles are put up, everyone is careful. Once the brick is put up, many people don’t notice. So, many people stir the cement, move back and forth on the brick, and some tools pull back and forth.In particular, some processes such as paints, coatings, carpentry and so on are laid behind the tiles.Therefore, the laying of good tiles should be covered with protective film, and it is required to lay a good paste for at least 24 hours or more before walking on it.
In order to improve the effect of ceramic tile and stone placement, it is generally preferred to use beautiful sewing technology. The gap is not yellow, moldy, and easier to clean.It should be noted that the stitch should be done as soon as the ceramic tiles are dry. To prevent the ceramic tiles in kitchen from being dry, the construction on the surface of the tiles will cause the loosening of the tiles, leaving the hidden danger of hollowing out.

What is the preparatory work for the tile paving?

/in /by

The tile paving is small and small. It seems to be very small. It seems to be very simple. It seems that there will be no big event, but it is always annoying if it is done. Details are very important, many of the problems, in fact, are not done in some details, tile paving is the same, with everyone to share some tiles paving, some often ignored small details.

The wall should be dealt with well. Some walls are cracked, or walls are connected to other materials, such as cement walls and woodworking boards. Before laying tiles, it is necessary to connect the wall cracks with wire mesh, then reinforce with cement, and then lay up tile again, so as to avoid cracking of later ceramic tiles.

Whether the tile needs water or not, it is necessary to see the specific situation. In the use of ordinary cement mortar paving, some of the higher water absorption of pottery tiles, that is what we usually say wall tiles, that is the need for water, and must bubble foot. And some floor tiles with low water absorption, such as polished tiles, marble tiles, etc., do not soak water, whether they stick to the ground or on the wall. There is another case. If it is paved with ceramic floor tile, no matter whether it is tile or floor tile, it needs no water. When the water is needed, you should pay attention to it. Every batch of tile time is as much as possible, and the water used is as clean as possible so as to avoid the color difference after the paving. There is also a point, the need to make water tiles as much as necessary to bubble water, how much to use in advance to bubble how much, especially when put to the back, do not make a whole body to bubble, if the bubble is not finished, it is unable to return.

About the powder of the tile billet. Magnesium Oxide and magnesium carbonate are a high temperature resistant white powder. Generally, the ceramic kiln floor tiles are at the highest temperature of more than 1200 degrees, when the tile bottom is close to melting (the expression may be inaccurate, but the tile embryo is soft). In order to avoid sticky stick of tile embryo and kiln, using the characteristics of high temperature resistance of Magnesium Oxide and magnesium carbonate, before the tile embryo entered the kiln, a layer of Magnesium Oxide pulp was brushed on the bottom of the embryo to play the role of isolation. This will avoid sticking sticky tiles and sticks in high temperature kilns. Therefore, sometimes we will find that there are many powders at the bottom of the billet, and we should try to remove the white powder before paving. Otherwise, it will cause the cement mortar to be stuck to the tile, causing the hollowing off.

Many people think that it is a waste of time to per pave tiles before paving. In fact, the old pottery people think that the front row of tile is to spend a little time, but in the row of tiles, can avoid the generation of some of the following problems, for example, when the tile, can look at the tiles of the supporting waist line, tile or processing tile and the main tiles with the main tile? Besides, there are obvious defects on the main tile surface, whether there is chromatic aberration, whether the size error is large or not. In front of the tiles, the old pottery also hopes that the owner can take out every tile that is to be used, and give a detailed account of the position, quantity and special requirements of the paving, which can avoid the paving error.

Before paving, we must clean up the wall. Before we scrape the putty wall, we need to shovel the putty and lay the tiles again. Otherwise, it will easily cause the hollow drum to fall off. If you want to use tile glue to paste the tiles later, you must make the wall level. If we use ordinary cement mortar to paste, we should pay attention to the proportion of cement sand, tile 1:3, floor tile 1:2, cement grade 32.5 cement. If the floor tiles are on the wall, it is suggested that tile glue or adhesive should be used for paving, so as to avoid the drums falling off later.

Why not use the stone for the decoration, to use the ceramic tile?

/in /by

Family decoration is a very important and grand thing, and the good or bad decoration not only affects the overall visual effect, but also related to the daily life of the use, In the entire decoration process, the choice of decoration materials is often very important. Is family decoration stone or tile?

The stone is cracked and fragile, and the processing requirement is very high. If it is not careful, it will cause fragmentation. Ceramic tiles are made by physical suppression and chemical firing. They are hard in texture and can be machined according to the actual decoration requirements of consumers.

Stone Mori hardness is only 2-3 grade, long time for the ground, the surface is easy to wear and wear. The ceramic tile is 4-7 degree Mori hardness, the surface adds the glaze protection, the product is super wear-resisting.

Stone is easy to break and fragile, especially large long boards. Even if the glued steel mesh is fixed, slotting and steel bars are easy to break when transporting and installing paving. Ceramic floor tiles are made by physical suppression and chemical firing. The texture is hard and dense. Generally, cars will not break through brick surfaces slowly.

The stone is mainly made of calcium carbonate naturally, with more cracks on the surface and easy to permeate. All kinds of stolen goods at home are easily infiltrated into the marble. The clean surface can not be cleaned at all, and the professional nursing price is expensive. The glaze layer on the surface of the ceramic tile is fired at high temperature. The stains are completely impervious and polished. The surface is smooth and easy to clean.

The nature of stone material causes small holes and crevices on the surface of stone, easy seepage and high water absorption, which is the reason why stone cleaning and nursing can’t be used for water. The glaze layer of ceramic bath tile is dense and smooth, and the water absorption rate is less than 0.3%. Therefore, tiles can be washed and cleaned with water.

The natural stone of the stone surface texture color difference is large, many defects, even if there is a uniform and unflawed stone, the price is also very expensive, the common stone will be filled with glue, dyeing treatment; Ceramic tile specialized production, raw materials, technology is completely controllable, no defects and chromatic aberration.

Stone is rough mining and simple processing, semi-finished products are not. At the same time, due to the non renewable quality of the products and mine resources, supply is not stable, replenishment is basically impossible, home installation especially large project in supply and time is difficult to control; The ceramic tile flooring is the finished product of the standardized industrial production, the size specification can be made according to the requirement, the product is bought in and out, the supply is stable, the quantity is big also can be delivered on time, the time limit is guaranteed.

What is the wall tile in the middle plate?

/in /by

Medium plate, that is, medium size; internal wall tiles, refers to the application, paving on the wall of a class of ceramic tile products; The inner wall tiles of the medium plate, as the name suggests, refer specifically to the medium size tile products specially applied to the walls. In recent years, with the popularization of large ceramic tiles in the whole ceramic industry, tiles have been expanded to a great extent on the ground placement and application. All kinds of large scale ceramic tile ground application solutions are also very sufficient, but the product is relatively small for the inner wall tiles which are focused on the large size tiles.

In the ceramic industry, which is popular in the ceramic tile market, there is a great market prospect for ceramic tile products in the middle plate, and it will show the possibility of explosive growth. which advantages of the wall tile in the middle plate?
1)the tile’s body is vitrified, low water absorption, and the product is pressed by relatively high tonnage press in the process of production, and the product is burned for a long time.
2)the ceramic floor tile surface texture is rich and the texture effect is excellent. The technology expression of the interior wall tile products on the enamel line and the surface printing process can be superimposed in a more complex way.
3)The inner wall tile has good seismic strength, which is that the body is more sturdy. In the process of production, a more fine ball milling machine is used to make the ball into the slurry.
4)The product size is more standard, the standard of the production process of the inner wall tile is close to the standard of the common full body marble tiles or rustic tiles production process, so the error of its later forming size is smaller.

The inner wall tile of the middle plate is a kind of ceramic bath tile product with low water absorption. In the construction of the wall, it is suggested to use the strengthened ceramic tile glue for laying on the wall. At the same time, we need to pay attention to the paving of it, please ensure that the base of the wall is neat and smooth. We must keep the seam paving during the paving process. The gap between tiles should be reserved between 1.5mm-3mm. Finally, after the paving is finished, it is recommended that the seams can be treated with beautiful seams, so that the overall effect will be better. Which difference between the inner wall tile and the traditional porcelain tiles?

the water absorption rate is different. The inner wall tiles belong to ceramic tiles. The water absorption rate is relatively low. Most of them are under the control of 1% or double zero. The traditional porcelain tiles belong to the ceramic tiles. The water absorption rate is generally high, and the water absorption rate is generally in 8%-12%.

The density of tiles body is different, the vitrification degree of the tiles body is higher, the density is higher, the anti damage strength is high, the traditional porcelain tile is the pottery body, the high water absorption and the low density of the tiles are the remarkable characteristics of the traditional porcelain tiles. Meanwhile, the anti destructive strength of the traditional Chinese tiles is also relatively low.

With different wear resistance, the wear resistance of inner wall tiles is higher than that of traditional porcelain tiles. Because of the high density and low water absorption, the traditional ceramic tile has low density and high water absorption, which causes the wear resistance of the traditional porcelain tiles to be less than the inner wall tiles on floor.

The performance of the wall tiles in the medium plate is different, and the surface of the wall tiles can be expressed by various kinds of deep and shallow grinding tools. At the same time, the surface can also apply a variety of dry grain effect. And the latter surface can also do various polishing techniques to perform the process, while the traditional porcelain tiles have no way to do it.

Is the better the whiter quality of tile?

/in /by

When the family decoration is purchased, many ordinary consumers are entangled in the color and lustre of the brick. Generally, they will choose the brick products with white brick. Although the color and quality of most tiles are not proportional to the quality, the normal quality of the tiles can not be determined by the color and lustre of the bricks, but the undeniable point: White tiles with large size tiles have great competitive advantages in product sales.

In the case of fierce market competition and serious product homogenization, the manufacturer makes a distinction between the quality of the product, and the selection of the white tile material and the iron removal process are more complex. Due to the related marketing, the low degree of quality of tile itself has created the effectiveness of marketing, resulting in general consumers blindly being followed and misled. Some ceramic manufacturers sell their inferior quality and color and lustre ceramic tiles in the market. For a long time, the ceramic tile products with deep color and lustre have left a very bad reputation in the market.

Some ceramic tiles have high requirements for whiteness, such as micro – powder tiles. It is necessary to improve the whiteness of white lines and transparency of transparent materials to improve the sense of the product. There are several ways to increase whiteness: One is to increase the amount of zirconium silicate; The two is to reduce the content of iron oxide in raw materials (white and transparent materials), so as to improve the permeability of products.
The most important factor affecting whiteness of ceramic floor tile is the content of ferric oxide and titanium dioxide in raw material, especially iron oxide content.

The raw materials for producing ceramic bath tile are mainly divided into two parts, feldspar raw materials account for about 80%, and clay materials account for about 20%. Generally, the content of ferric oxide in raw feldspar material is less than 0.2%, and the content of feldspar iron oxide in finishing (such as water mill) is less than 0.08%. The content of iron oxide in clay materials is about 1.2% ~ 1.8%, and the content of iron oxide in washed clay is about 1.2%.
The iron oxide in the green body is mainly carried by clay materials. In order to improve the whiteness of ceramic tile flooring, we must control the content of iron oxide in clay and choose refined clay. For example, the main indicators of ultra white washed clay produced by some manufacturers are: The content of iron oxide is less than 0.5%, generally around 0.4%, and the electric furnace is 90 degrees white, and the firing degree of kiln is 82 degrees. High strength and proper loss of ignition will not cause difficulty in forming or black heart when firing.

The main means to reduce the content of iron oxide is to select high quality mineral resources and two to remove iron from water.
After processing, the composite white iron oxide with low content and high strength meets the needs of tile production. However, it should be noted that some ultra white mud is very harmful to tile production when it is processed to increase whiteness and add a lot of quartz powder. Some of the northern clay with high whiteness and high fixed carbon content and large loss of burning loss is used as raw material. Although the clay whiteness of the synthesized clay is high, it is easy to produce black heart, and its strength is low, and it is not easy to form.

The whiteness of ultra white mud can not be examined solely, but also the brightness of the simulated products.
The general method of detection is: 70% of the billet was mixed with albite and 30% super white mud. After mixing ball milling, the cake was fired and the whiteness was measured in the furnace. The whiteness measured in this way is the whiteness reflected in the actual production. There is also a simple way to soak the burnt white mud cake into the water to see the change of whiteness after soaking. All iron oxide with high content of clay, whiteness of white mud super hard; low iron content, whiteness of generally not more than 10 degrees.

In addition to whiteness, mud mobility and forming strength are also important indicators of ultra white mud. Poor fluidity of mud will cause difficulties in ball milling. When the forming strength of the slurry is low, the product will crack easily.
The core index of ultra white water washing mud is: Low iron oxide content, high forming strength and whiteness after porcelain. Using ultra white mud, the production cost can be reduced and the production cost can be reduced without or less use of zirconium silicate, and the problem of excessive radiation caused by the use of zirconium silicate is also avoided.

Home decorate, recognize these sizes of the tiles

/in /by

As we all know, tile is the best building decoration material, its stable physical and chemical properties are also very worthy of praise, but for many owners who want to use ceramic tiles, they are often faced with a great variety of tile products. So, for the owners who want to use tile, what do they care about most, the size of tile should be their most concerned, because the size of the ceramic tile will eventually affect the construction cost of the later tiles, the size of ceramic tiles is too big or too small, it will increase the cost of tile paving and the size of ceramic tiles is too big for the professional. The standardized paving requirements are higher and more strict, and the size of ceramic tiles is too small, which will greatly increase the construction time of the builders on the tiles, which leads to the higher cost of the construction.

800 * 800mm specifications of ceramic floor tiles have always been the highest frequency of use, which is beyond doubt, and is obvious to all. At the same time, we are most common in this size of ceramic bath tile. This size of ceramic tiles is the most mature and stable in all aspects of technical parameters control because of the use of all manufacturers. The size of the specification size, 800 * 800mm sizes of ceramic tiles are currently the most widely used, its position is not subversive, as for the construction paving, at the present stage of the tile workers, the 800 * 800mm specifications of the tile construction paving is the most skilled.

600 * 600mm sizes of tiles have an irreplaceable importance in the application of the whole space. The use of this size ceramic tile in small space can greatly reduce the loss rate of the tile in the process of paving, so the size of the tile has its unique complementarity and the performance of the more ceramic tiles in the construction. More flexible.

When it comes to the 300 * 600mm price ceramic tile, I believe that many people first impression will think of marble porcelain tiles, that is, inner wall tiles. It is true that the application of the 300 * 600mm tiles and wall surface is very widespread and common. At the same time, many building walls are basically used in the daily life of the tiles, compared to the larger specifications. For ceramic tiles, the construction of 300 * 600mm on the wall is much simpler.

400 * 800mm of this size, the application of the wall tiles is the extension and supplement to the 300 * 600mm specifications. The application on the ground is the filling of square size tiles, and because of its 1:2 ratio, the application ground can greatly enhance the three-dimensional sense of the whole space. It is also convenient in the construction and paving, and there is not too much requirement.

For 300 * 300mm specifications of small ceramic tiles, in small space application is very extensive, such as: toilet, balcony, kitchen is usually use this size of ceramic tiles, but also because of the flexibility of its specifications, in small space paving construction is more convenient, can change more.

600 * 1200mm size of ceramic tiles discount, in large space and large scope application of its effect is very shocking, while the length of the size is also more solid, the proposed pursuit of fashion, front style decoration owners can refer to the construction, because its long bar in the placement of attention to the tiles and tiles must pay attention to the level title At the same time, adequate tiles should be reserved, and 2-4mm tiles should be reserved.

150 x 900mm specifications, the size of this type of tile is mostly wood grain tiles, and more is applied to the bedroom, study, restaurant, or other applications. If you want to use this type of ceramic tile, then the whole space will take some thoughts to conceive the collocation, but it is the best choice for the owners who like the wood grain.

600 x 900mm size tiles are between rectangular and square, well compatible with the rectangular size and square size of their advantages, convenient for construction and paving, and also a strong sense of stereoscopic.