Posts

How Mopping Your Floor?

/in /by

Use hot water. Whether you are creating a solution to wash your floor, or just using water, you should use hot water. Hot water will help cut through grime. Ultimately, by using hot water, you’ll decrease the chance that you’ll need tougher solvents that could damage the marble.


Focus on distilled water. Distilled water is water that has gone through a process to remove minerals and other impurities. By using distilled water, you’ll reduce the chance of discoloring or staining your marble. You can buy distilled water at just about any grocery store or box store. It is usually cheap.


Add a mild detergent to your water. Add a mild detergent such as 2-3 drops of dish soap into a bucket with your hot, distilled water. Follow the directions of the soap and dilute it with an appropriate amount of water. Mix your solution thoroughly. Make sure to only add pH neutral soap to your water.


Harsh chemical solutions like bleach, hydrogen peroxide, ammonia, and vinegar can be damaging to your floors. Avoid using these on marble. If you prefer, you may be able to use a commercially prepared marble cleaner. Simply follow the directions on the bottle and then clean as you would with a water and detergent solution. Some products include Stone Tech, Resolve, or Simple Green.


Use a soft mop on your floor. Take a mop with a soft mop head (preferably microfiber) and dip it into your solution of detergent and water. Wring out the mop head to relieve it of excess water and systematically mop your floor. Do short strokes that overlap. Rinse and wring out the mop head after you’ve covered 10 to 20 square feet (1 to 2 square meters). This might vary depending on how dirty the floor is.

How to Maintaining Your Stone Tile?

/in /by

Evaluate the condition of your stone. Cracked wood marble tiles will accumulate buildup and dirtiness more quickly than those without any. These may need to be replaced or repaired. Uneven wall tiles may require a professional to grind, hone, and polish them flat. Note any stains and try to determine what caused these.

Knowing the source of a stain will make it easier for you to eliminate later if general cleaning techniques don’t work. Avoid abrasive and acidic cleaners. Abrasive and acidic cleaners will damage to your stone. Check the labels of all cleaners before using them to make sure they don’t contain either of these. Before using a cleaner, test it on an out of sight part of the stone to verify that it won’t damage or discolor.

 

Cleaners that are specially formulated for the kind of stone used in your shower will likely be the safest to use. Remove excess moisture from the tile after showering. Water remaining on your white tile will eventually evaporate, leaving behind minerals that cloud your stone, dirtiness, and more. After every shower, use a squeegee or soft towel to wipe away excess water and prevent this from happening.

Many squeegees come with suction cup hangers that you can attach to the wall of your shower. This way, your squeegee will be easily accessible after showering. Protect the condition of the tile with a non-slip mat. Your feet can grind small debris, like dirt, into your stone tile, wearing it down over time. This can cause it to lose its luster. Place a non-slip mat on the tile and vacuum under it occasionally to suck up these small particles.

Clean mats at least once a month to prevent stains from hiding underneath them and increasing in severity over time. Polish out etch marks. Etch marks are usually caused by an acid. Remove any dirtiness first with general cleaning methods. Apply a suitable stone polishing powder to the marble tile. Use a damp cloth to rub the powder into the stone in a circular motion. Continue rubbing until the etch mark disappears.

Some of your shower products may contain acids. Take care to keep these off your stone to prevent etching. Etching that is especially deep may be impossible to remove with polishing powder. In these cases, call a stone repair or maintenance professional.

How to Doing Routine Cleaning a Stone Tile Shower?

/in /by

Wipe away loose buildup and grime. Wet a clean, soft cloth, like one made of microfiber, in warm water. Firmly wipe down all of your shower’s stone tiles and the grout in between. This will make it easier for you to find and target more severe buildup and hidden stains. Soft clothes will be the gentlest on the finish of your stone. Rough fabric, over time, could cause the surface of your stone to pit or cloud.

Scrub grout with a toothbrush and a mild detergent. The narrow crevices between cement tiles and filled with grout are a prime location for buildup. Use a mild detergent, like dish soap, warm water, and a toothbrush to scrub the grouted cracks between ceramic tiles. Rinse the area thoroughly afterwards and repeat as necessary until the grout is clean.

Because grout is often dirtier than the tile itself, clean the grout first to prevent it from spreading to the kitchen tile. Avoid using general grout cleaners when cleaning the grout of natural stone tile. These often have ingredients that can damage your stone. Stiff bristle brushes can harm the finish of your stone and cause scratches. Only use soft bristle brushes and soft cloths when cleaning.

Clean the stone with a mild detergent or stone soap. Mix together warm water and a couple drops of mild detergent, like dish soap. Stir the solution to distribute the soap. Dip a soft rag into the solution, wring excess liquid from it, and use it to wipe down the casstle tiles. Rinse the tiles frequently as you do so.

Soaps that are formulated for the natural stone used in your shower can be found at most hardware stores. Cleaners that are acidic can damage your stone tile. Only use cleaners that are pH neutral (a 7 pH rating), which should be indicated on the cleaner’s label information. Using more soap isn’t always better. Too much soap in your solution could result in streaks or a film remaining on the marble tiles after cleaning.

Cut through soap scum with an ammonia and water solution. Soap scum is a common problem and it can be difficult to remove. Cut through it with a solution of a half cup (237 ml) ammonia and a gallon (3.8 L) of water. Apply the solution to the tile with a clean, soft cloth.

Using ammonia to clean your stone too frequently can negatively impact its appearance, causing it to dull. Stay on top of general cleaning to prevent soap scum from building up. This way, you’ll only have to infrequently use ammonia. Dry the stone after cleaning. Avoid leaving cleaners on your stone for long periods of time, especially ones that can cause dulling or fading, like ammonia or hydrogen peroxide. Rinse the tiles design thoroughly and then wipe them dry with a clean, soft towel.

Simple and Practical Marble Ceramic Tile To Buy Seven Standard

/in /by

The similar appearance, the superior performance of ceramic tile, marble together makes this different quality marble tiles become popular with users of the popular building materials, but in the face of a variety of marble tile brands on the market, with only a bibulous rate, the basic testing factors such as stiffness is not enough to help us distinguish good marble tile,The first marble tile quality evaluation standard of the industry “marble ceramic tile 7 star standard” came into being, let’s look at how simple and specifically choose marble ceramic tile.


1.Fidelity
In terms of its nature of ceramic tile, marble tile ceramic tile is a kind of imitation wood, imitate the texture adornment effect is its important value, so the fidelity is selected the first parameter to the ceramic tile, marble to emphasize its fidelity: stone should ≧ 99.9% reduction degrees, will be in comparison with natural marble, ceramic tile on the premise of removing impurities, higher similarity is preferred, stone should ≧ 99.9% reduction degrees.
2.The duplication
Stone attractive appreciation of a play feature lies in its unique natural, to condemn the change of grain, and used in ceramic tile decoration, in order to avoid duplication of texture bring stiff feeling of the space, so the ceramic tile on the stone should try not to appear to repeat: stone texture should not repeat area ≧ 5 square metre, extract a case of tile ceramic tile on the floor, to see if the pattern repeat, repeat degree is lower, the better decorative effect.
3.Accurate printing degrees
Inkjet technology is nowadays the main technology of high-quality marble tile surface color layers of permeable brick should be of high quality marble, perfect reduction natural color of natural stone material, real and solid: picture for at least 360 dpi precision of 0 grid and high precision spray printing, the scene to identify pattern is clear, the place of ceramic tile 10 cm distance to the naked eye can not see the grid.


4.Bo changes degree
In essence, the water absorption rate is the criterion, the low water absorption rate is not easy to absorb dirt, the quality is better. Good marble tiles should be very low water absorption, the higher the degree of vitrified, bricky system stronger, more not easy ooze water: water absorption should be ≦ 0.05%, the water droplets on the back of ceramic tile, slow water infiltration or not bibulous, the greater the density of ceramic tile, the better the quality.
5.Stiffness
As ceramic tile, everyday use in the family in general can’t avoid all sorts of friction or collision, so the stiffness is also one of the most important elements of ceramic tile, marble in order to avoid the ceramic tile is easily damaged, durable marble tile should have higher hardness: thematic mohs hardness ≧ 6, the scene with blades and other hard iron swiping in ceramic tile surface, no scratches on the top grade.
6.Self-cleaning degrees
Once decided to use ceramic tile, decorate is generally the use of large area, if the higher the degree of self-cleaning ceramic tile, is that much more convenient to do when using, starting from the users the best experience, marble tiles need good self-cleaning ability, can withstand the daily life of the stain liquid such as: the anti pollution coefficient must be ≧ 5, ink, soy sauce, vinegar, etc of drop in ceramic tile surface, after a short waiting to wipe clean, no residue after taste.
7.Mass density
Mass density is closely related to ceramic tile weight, in the case of equal size, weight of ceramic tile ceramic tile quality means that the greater the more thick, material, density higher and higher, bricky system has stronger: ceramic tile should ≧ weight 25 kg per square meter, compare different marble tile cutting into the same specifications weighing, the person that weigh is preferred.