Posts

How Oiling Your Soapstone tiles Surface?

/in /by


Wait a full day to treat your Soapstone tiles following installation. After having your Soapstone tiles surface put in, hold off on handling it for at least 24 hours. This will give the adhesives used during the installation process time to finish curing, ensuring that each piece stays remains secure for a good long time.


Putting off cleaning or oiling your Soapstone tiles for a while will also give you time to consider whether you want to oil it at all—some homeowners prefer to let the stone develop its own unique patina organically through regular use. Clean the surface with soap and water.


Before you begin oiling your Soapstone tiles, saturate a soft, clean, lint-free cloth, microfiber towel, or sponge with a mild soapy water solution and use it to go over the entire surface. Then, wring out your cloth, re-wet it with clean water, and wipe the surface again to rinse it. Be sure to soak up any standing water or traces of soap remaining on the surface prior to proceeding.


A quick wipedown will help remove dust and other debris so it doesn’t end up in your initial coat of oil. Drizzle a small amount of mineral oil onto the surface. Use just enough oil to spread a thin coat onto the surface by hand. Pour the oil directly onto the Soapstone tiles—it’s naturally non-porous, so it won’t absorb oil or moisture.


The fact that Soapstone tiles has a solid finish also means you won’t have to worry about it feeling slick or greasy as a result of becoming clogged with oil. of oil for every 1 square foot (0.093 m2) of Soapstone tiles should be plenty.}} Tip: 1 teaspoon (4.9 mL) of oil for every 1 square foot (0.093 m2) of Soapstone tiles should be plenty.

How to Marble a Wooden Floor?

/in /by

Creating a faux marble look on a wooden floor can be an interesting way to cheer up a fading floor. It’s also a lot easier to care for than a real marble floor! This article explains how to marble a floor in your home, using a black and white square checkerboard design. This will take up to a week to do and is fairly intensive work but the end result is worth the effort.


Sand the wooden floor completely. Remove all furniture from the room or area and any rugs. Be sure to sand every part of the floor that is to be marbled. Apply three coats of a light-coloured, flat, oil-based paint. Apply across the entire floorspace. Lay a grid of squares to create the black and white checkerboard square appearance. Measure exact squares across the entire floor space using a measuring tape and pencil.


Draw over the lines using a felt tip pen so that you can see the borders of each square easily when painting. Leave a general border space of 20 centimeter (7.9 in); this will “frame” the entire floor feature. Work in small areas at a time. Start by painting the light or white coloured squares using off-white white paint.


Start to create the mottled marble effect. While each off-white square is still wet, create small brush streaks using a combination of black, tan and grey. Use a dry brush to blur in the streaks. Leave these squares to dry thoroughly for 48 hours. Once dry, use masking tape and paper to protect them from the next step, painting the the dark colour.


Cover each light square completely in paper and be sure to make the masking tape meet the edges exactly. It takes a bit of work but it is worth doing well. Use a sponge to dab on black and dark green paint on the uncovered squares. This paint should not be brushed on, as you want it to appear streaked.

How to Install a Kitchen Backsplash?

/in /by


Adding a backsplash to your kitchen is a great way to create atmosphere with color and texture. Thankfully, the process of applying a backsplash is easy. Here is the best way to apply a backsplash to your kitchen, using both traditional tiles and a peel-and-stick method.


Firmly attach your tiles. Press them into the tile adhesive on the wall, using a level to make sure they are even. Push them a few times to make sure they are secured to the wall. If your tiles are not attached together in sections, use spacers to make sure they are all evenly spaced. Wiggle the tile a little bit against the wall to ensure suction with the adhesive.


Completely cover your wall. Attach all remaining tiles to your wall using this method, until you reach the edges. Before you stick your tiles to the edges of the wall, cut off any excess or oddly shaped corners to make sure the fit is perfect. Always cut out holes for outlets or odd edges prior to attaching the tile to the wall.


Any empty spaces can be filled with pieces of spare tile you cut to size with your tile cutter or utility knife. Apply grout. Use your (cleaned) trowel to spread grout evenly across the tiles. Don’t worry about covering the tiles, as that is what is supposed to happen. You will remove the unnecessary grout later.


Spread the grout at a 45 degree angle in a sweeping pattern. Allow a few minutes for the grout to set, and then use a damp sponge to clean off excess grout. All of the cracks between the tiles should be filled, while the remaining tiles should be cleaned of all unnecessary grout.

Measuring Tiles

/in /by

Measure the size of the tiles you want to use and any tile spacers or grout. Decide how many tiles you will need to use to complete your pattern. Ensure level tiles with the use of a batten, or wooden straight edge. Do not measure the tile according to the ceiling or floor, since these surfaces are not always level. Place a batten horizontally across the wall, and use a level to make it straight.

Pin the batten on the wall. Mark where the wood tiles will go with a pencil, including spacers or grout. The batten will help you to keep the tile straight and evenly spaced, so do not avoid this time-consuming step. Use a vertical batten for your first tiles as well. Pin a level vertical batten in place. This will ensure your first wall tiles are at a 90 degree angle.

Apply a layer of glue to the area above the batten with a notched trowel. You can use a vertical straight edge to help align the tile uniformly. In small areas, you may need to apply the glue with a brush, but make sure it has a notched surface. Place a tile spacer between the small tiles as you set them into the glue to allow space for grout.

Press the tile into the wall with a wooden board. Allow the cement tiles to dry according to adhesive directions in small areas, so that you can concentrate on making the tiles straight. Wipe away any excess glue with a wall scraper. Then, wipe away the tops of the tiles with a wet rag.

Cut porcelain tiles to go near the edges of your walls. You will need to use a wet cutter with a blade that goes in water. Measure each tile before cutting for a good fit. Allow the tiles to dry for at least 24 to 36 hours. The glue directions should specify the necessary time.

Spread grout over the surface of the tile with a grout float. Choose a tile that is water and mold resistant. Clean the surface of the tile with a wet sponge. Run the wet sponge over the surface of the tile. Allow the grout to dry completely. Polish the surface of your tiles with a dry cotton rag. This should remove any remaining grout residue.

How to Refinish Marble Tile Floors?

/in /by

Refinish your marble tile floors for less than $100. This method also removes the thin layer of grout which has been left if grout was installed and not immediately cleaned afterwards.

Section your floor into smaller work areas. If you use small 5 x 5 ft sections it will make your work easier to keep clean. Use rolled up towels or drop cloths around the 5′ x 5′ perimeter to limit the amount of kickback spray from the spinning motion that the angle grinder generates. If you don’t do this, the milky colored spray will get everywhere.

Wet the section of the floor with water and cover the calacata tiles with a nice layer of water (more is better as it provides lubrication for the pad). Add a small amount of buffing compound and mix thoroughly (just spread it around with your hand). Be sure the water/compound mixture completely covers your work area. Make sure the water/compound mixture is milky and pretty dissolved before buffing. Be sure to wear gloves when doing this as the buffing compound is acidic and will dry up and irritate your skin.

Use the angle grinder with the nylon pad to go over your wood marble tiles one by one. Let the angle grinder do the work and just hold the sucker steady. It will take a bit of getting used to at first, but you’ll get the hang of it. Spend least 30 seconds on each tile to make sure the scrapes, scuffs, scratches are buffed down and smoothed as much as possible. Keep the grinder moving in small circles to polish the santana stone tiles evenly.

After you have finished the sectioned area, pour clean water over the area and mix it around making it wet again. Use a shop vac and suck it all up. Then if necessary, rinse with clean water and suck that up too. Move onto the next section until every tile is done.

How to Choosing a Blade and Taking Safety Precautions Before Cut Marble Tiles?

/in /by

Pick a diamond blade for your saw or angle grinder. Diamond blades have a harder cutting edge, making it easier for them to grind through tough materials like stone or marble tile. Purchase a blade for a wet saw or an angle grinder depending on what you plan on using.

Look for diamond blades at your local hardware store or online. The size of your blade depends on the model of your machine. Check with the instruction manual to see what size blade it requires.

Mark the line you’re cutting on the casstle tile with a pencil. Set a straightedge on top of your tile and trace along the edge with a pencil to mark it. The mark won’t wash off when you use a wet saw, and it can easily be rubbed off the spots tile when you’re finished. If you’re making a curved cut, use a compass to trace a perfect circle.

Tip: If you don’t want to mark your calacata tile directly, place a straight piece of masking tape on the tile and use a marker to draw your line on it. It’s okay to cut through the tape.

Wear safety glasses, earplugs, and a respirator. Cutting through marble tile kicks up a lot of dust, so protect your eyes, nose, and mouth. Since using the saw or angle grinder will be loud, put in earplugs so you don’t damage your hearing. Most hardware stores should carry all of the safety equipment you need. You may wear work gloves if you want, but they’re not necessary.