Posts

How Tackling Tough Interior Stains?


Blot up spills right away. Use a clean, dry towel to pick up any spills on your sandstone tiles. Be sure to dab and blot the area instead of wiping it. Wiping the spill around can create a larger stain by moving the food or liquid around the area. Most liquids can stain your sandstone tiles but some that are particularly bad include wine, fruit juices, and coffee.


Avoid the use of cleaners that contain harsh chemicals and abrasives. sandstone tiles is a very porous stone and it can be discolored and damaged by a wide variety of cleaning products. In particular, acidic cleaners can discolor the surface permanently. Tip: sandstone tiles is prone to discoloration and it can’t be cleaned with the common cleaners you use in other parts of your house.


Thus, if you are looking for a surface for your tiles or flooring that is strong and can take a beating, sandstone tiles is not for you. Make a baking soda paste if plain water can’t get a spot off. It’s easy to make a great alkaline sandstone tiles cleaner by mixing up a paste of baking soda and water. Put a couple of tablespoons of baking soda in a small bowl and mix in a few drops of water.


Stir the mixture with a spoon and keep adding water until the mixture is a thick paste. You can also buy specific natural stone-cleaning products online or at many home improvement and hardware stores. However, a simple baking soda paste is likely to work just as well. Apply the paste to the stain and scrub it with a soft-bristled brush.


Smear the paste onto the stain on the stone with the spoon you used for mixing. Let it sit on the surface for about 15 minutes. Then scrub the surface with a soft brush. You can use a variety of types of brushes, including a home cleaning brush, a nail brush or an old toothbrush. Wipe the paste off with a clean, damp cloth.

How Attaching Your marble tiles?

Install your kitchen sink if necessary. If you had to remove your kitchen sink when removing your old marble tiles, be sure to reinstall it before adding the new material. Start by following manufacturer’s directions to install the faucet followed by detergent and dispenser mounts. Now, attach the sink, supply lines, and drain pipes.


Always apply a ribbon of plumber’s putty before installing the faucet and sprayer bases. Use caulk to attach the sink rim to its opening. Seal the drain and tailpipe with caulk or with a gasket—whichever the manufacturer recommends. Be sure to turn your water on and check for leaks before installing your marble tiles.


Stick painter’s tape to the top edges of the cabinets for protection. Try to cover at least the top 1 inch (2.5 cm) of the cabinets, although the more the better. This will ensure that no silicone adhesive touches their faces. Purchase painter’s tape from any home hardware store or online supplier.


Install ledgers in areas of low cabinet support. While marble tiles can be placed directly on top of cabinets, their weight shouldn’t be underestimated. Take a look at your tiles design and look for areas that have the least amount of cabinet support. Now, install 1 to 2 inch (2.5 to 5.1 cm) ledgers into the walls on the sides of the cabinets to add support.


Attach each ledger using an electric drill and the screws provided. Purchase ledgers from home hardware stores. Be sure to take measurements of the areas that need ledgers before purchasing any. Apply silicone adhesive beads to the top of the cabinets. Start by applying a 2 to 3 inch (5.1 to 7.6 cm) thick bead of adhesive to a corner and then working your way around the top of each cabinet.

How Using Concrete?


Clean debris off the wall with water and a sprayer. Remove as much debris as possible from the wall so the concrete bonds cleanly to it. Spray away most debris with water from a garden hose. Also, try mixing 1 cup (240 mL) of a mild dish soap into about 5 US gal (19,000 mL) of hot water to scrub off tough stains with a concrete brush.


Use a power washer for extra cleaning power. If you don’t own one, see if your local hardware store has one to rent. For tough stains you can’t quite remove by hand, mix 1 cup (240 mL) of trisodium phosphate in about 1 US gal (3,800 mL) of water. Scrub it into the stains with a brush before rinsing it off with clean water.


The chemical is strong, so cover up with long-sleeved clothing, gloves, goggles, and a respirator mask. Mix surface bonding cement with water to a pasty consistency. The easiest product to use on a cinder block wall is surface bonding cement. All you have to do is pour the cement into a container such as a wheelbarrow, then stir in the water with a shovel.


You need approximately 4 cups (950 mL) of water for an 80 lb (36 kg) bag of cement mix. Shop online or visit your nearest home improvement store for cement and all the tools you need to apply it. With surface bonding cement, you don’t need to apply a concrete bonding adhesive.


If you wish to use another type of cement or concrete, also get a bag of adhesive. Mix it with water and spread it on the wall first. Wet a section of the wall again to prepare it to bond with the cement. Spray the entire wall thoroughly with water from a garden hose. Then, go back to a section of the wall to work on first. Spray it once again with water.

How to Marble a Wooden Floor?

Creating a faux marble look on a wooden floor can be an interesting way to cheer up a fading floor. It’s also a lot easier to care for than a real marble floor! This article explains how to marble a floor in your home, using a black and white square checkerboard design. This will take up to a week to do and is fairly intensive work but the end result is worth the effort.


Sand the wooden floor completely. Remove all furniture from the room or area and any rugs. Be sure to sand every part of the floor that is to be marbled. Apply three coats of a light-coloured, flat, oil-based paint. Apply across the entire floorspace. Lay a grid of squares to create the black and white checkerboard square appearance. Measure exact squares across the entire floor space using a measuring tape and pencil.


Draw over the lines using a felt tip pen so that you can see the borders of each square easily when painting. Leave a general border space of 20 centimeter (7.9 in); this will “frame” the entire floor feature. Work in small areas at a time. Start by painting the light or white coloured squares using off-white white paint.


Start to create the mottled marble effect. While each off-white square is still wet, create small brush streaks using a combination of black, tan and grey. Use a dry brush to blur in the streaks. Leave these squares to dry thoroughly for 48 hours. Once dry, use masking tape and paper to protect them from the next step, painting the the dark colour.


Cover each light square completely in paper and be sure to make the masking tape meet the edges exactly. It takes a bit of work but it is worth doing well. Use a sponge to dab on black and dark green paint on the uncovered squares. This paint should not be brushed on, as you want it to appear streaked.

How to Plan Tile Layout?

If you’re thinking about installing a tile floor in your home, it’s important to take the time to figure out the best way to arrange the individual tiles. In most rooms, square and rectangular tiles will fit together in a simple grid pattern. First, establish a series of layout lines to serve as a placement guide by finding the midpoint of each wall and drawing a line across to the opposing wall.

From there, you can begin dry-fitting the tiles around the room’s center point, working your way outward in manageable sections to avoid uneven spacing. Mark the midpoint of each wall. Divide the total length of the walls in half, then draw a small notch or dot on the floor at this spot using a carpenter’s pencil.

Aligning the midpoints of each wall will help you find the room’s center. For a wall that’s 16 feet (4.9 m) long, for instance, you would make your mark at 8 feet (2.4 m). If the room you’re measuring is perfectly square, you can go ahead and draw a line straight across to the opposite wall save time.

Draw a line connecting the midpoints of both walls. To ensure that the line is straight, run the tip of your pencil along the edge of a yardstick or straight edge, using a framing square to ensure a precise 90-degree angle. Slide your yardstick down and double-check its orientation every few feet to keep the line from becoming crooked.

You can also use a chalk line tool for greater efficiency and exactness. Simply extend the retractable wire between the 2 walls, then pull up and release the wire quickly to leave behind a perfectly straight line of chalk. Repeat the process on the room’s shorter walls. Measure the length of the remaining pair of walls, then mark the midpoint of each. Draw a line connecting the opposing midpoints through the center of the room.

How to Clean Tile Floors with Vinegar?

The right floor tiles can lend a look of subtle sophistication to almost any room in your home—until they get dirty, that is. After a while, dirt and mildew can begin to build up on the surface of textured tiles and down in the grouting, leading to unsightly discoloration. Cleaning floor tiles can also be a tricky task, as many types of cleaners can inadvertently fade or damage porous materials like natural stone. Luckily, there’s a convenient solution sitting right in your kitchen. With just a bottle of ordinary vinegar and a little determination, you can clean and polish your tile flooring, extending its lifespan and leaving it looking like it was just installed.

Talk to your local hardware store about the trowel size that they would recommend for your particular project. Usually, glass tiles come in sheets and trowel with smaller notches will be needed. However, if you are using larger glass tiles that are not in a sheet, the average 3/8″ trowel will probably be better.

Lay your tiles. With the mortar in place, you can start setting out your tiles or tile sheets. Simply press them firmly into the mortar; push it solidly against the surface but remember that it’s not toothpaste. You don’t want to push the tile so that you disturb the mortar. You just want to get the tile to stick. Try to start in a corner or against a wall, to cut down on the amount of cutting and sizing that you need to do. Insert tile spacers between the tiles or tile sheets as you go.

If you are using tile sheets, you can cut the sheets as needed to create a sheet of any size or shape for your project. You can also cut out the middle of a sheet in order to make space for outlets. Simply use a utility knife to cut the mesh backing.

Cut tiles as needed. You will likely have a space that does not perfectly fit the tiles that you have, create a need for only a portion of a tile. In order to fill these gaps, you will need to cut the tiles to size. You will need to use a wet saw with a blade designed for glass in order to cut glass tiles. Be very careful and keep your fingers as far away from the blade as possible.

How Deep Cleaning the Tile?

Pick a pH-neutral cleaner. You don’t want an acidic or basic cleaner for this type of polished tile, so pick a cleaner that states it is pH neutral. You can find special cleaners specifically for quarry floors, if you prefer.

You can also make your own cleaner. Mix 0.5 cups (120 mL) of baking soda into 1 gallon (3.8 l) until the baking soda is completely dissolved. Add 5 drops of liquid dishwashing detergent, and stir gently to combine. Dampen a mop with the mixture. Once again, you don’t want to use a large amount of cleaner or water on this type of floor. Therefore, make sure you wring out the mop well once you’ve dampened it with the cleaner.

Mop the floor. Run the mop over the floor, focusing on particularly dirty spots. Scrubbing is fine on the dirty areas, though you don’t want to use anything too abrasive. Keep in mind that this vatican tile will always have a matte finish. You may need to scrub the grout a bit harder, but it will likely still get darker over time.

Rinse the floor thoroughly. You don’t want to leave cleaner on the floor, as it can damage the tile. Rinse it off with warm water, making sure you get off all the cleaner before moving on. Dry the floor with a dry mop or rag. Once you’ve rinsed the floor, dry it off with a dry mop. You can also use a rag, if you prefer. You just don’t want to leave water on the floor, even to “soak” stains.

Use a clean wet towel and wipe your floors so you can get as much of the leftover splash and residue from the buffing compound off the floors and fixtures. Then go over your wood marble tiles once again with a dry towel. Finally, after your tiles and grout lines are dry, use a stone/marble sealer to seal your calacata tiles. Two coats are sufficient and your floors will look as good as new.