Posts

How Doing a Routine Cleaning?

Sweep away and dirt or debris. Any loose dirt, debris, or dust should be swept from cement floors or walls before you begin cleaning. Use a broom to sweep the cement as clean as you can before applying a cleaner. When sweeping down a cement wall, lay down a tarp to catch loose dirt, debris, and dust.


Put on protective gear if necessary. When using chemical cleaners, such as degreasers, gloves and goggles are generally necessary. You should also wear older clothing, regardless of what kind of cleaner you’re using, as cleaning cement may get messy. Prepare a cleaning solution. Mildly dirty cement can be cleaned with mild laundry detergent diluted with warm water.


In a bucket, mix a third cup of your detergent with a gallon of water. When using degreaser, consult the label to figure out the proper degreaser to water ratio. Pour the solution on the concrete. It’s best to work in sections, especially when cleaning a large amount of cement. Pour enough of your cleaner over the cement you’re working on to get it thoroughly wet.


For very dirty concrete, allow the cleaner to sit for a few minutes before proceeding to clean it. Scrub the concrete. Use a deck brush to scrub your cleaner into the cement. Work the cleaner in until you’ve removed any troublesome layers of dirt and dust, and any obvious stains or set in dirt.


For very dirty floors, let the cleaner sit for five to ten minutes after scrubbing it once. Then, repeat the process. Rinse with a hose or pressure washer. A pressure washer is the best means to remove a cleaner from cement. These can be rented at most hardware stores. If you do not have a pressure washer, a high pressure hose can be used to rinse the cement.

How to Buff Floors?

If you have scratched or scuffed floors, buffing them can refresh their shine. You can improve the look of your floors by buffing them by hand, but it’s best to buy or rent a floor buffer, which uses slow speeds and high pressure to remove and replace the top layer of finish on your flooring. You can buff any type of floor, whether it’s wood, vinyl, concrete, or tile.


Before you buff your floor, make sure you secure the area and clean the floor to remove any grime. Then, use a microfiber cloth or a spray buffing machine to restore your floor’s shine. Rotate your machine back and forth as you move across each section


Although the buffer is doing most of the work for you, rotating it will help you achieve a better result. Not only does it ensure the buffer covers all of the surface area, but it will also help you really work areas where there are scratches or scuffs. Your motion should swing back and forth like a pendulum.


Move backward as you work so you don’t step on the buffed sections. This helps you avoid stepping on the parts of the floor you’ve already buffed. You don’t want to step on the buffed areas because they will be very slippery. Also, you don’t want to mess up the finish. Walk slowly so you don’t accidentally trip over your own feet.


Hold the buffer over scratches and scuffs for a few extra seconds. As you work, look for visible scratches and buffs. It’s okay to give these areas special attention by holding the buffer over them for a few extra seconds. Additionally, you can make several passes over them. If you still notice a scratch or scuff after you finish, you can try hand rubbing it with a soft cloth soaked in buffing solution.

How Maintaining Your Tile Floor?

Clean tile floors regularly. When it comes to maintaining tile, the best solution is prevention. By sweeping, vacuuming and polishing your flooring on a consistent basis, there will be less chance of stain-causing substances accumulating underfoot. Be on the lookout for places where dirt and debris have a tendency to collect, especially in corners, beneath furniture and around the baseboards.

Aim to sweep or vacuum your tile floors every couple of days, and to mop or give them a more extensive wipedown about once a week. Neglected wall tile will quickly begin to advertise itself. If you allow it to get bad enough, it may even negatively affect the value of your home.

Wipe up spills and messes right away. When left untreated, even the smallest spill can become a stubborn stain. As promptly as possible, blot the affected area with a clean cloth dampened with warm water or a small amount of vinegar solution. Tracked-in dirt and food particles should be swept up so they don’t get ground into grout or rough surfaces.

Gradually apply more vinegar as need until the stain begins to come out. Responding to messes quickly is especially important if you have light-colored tile or grout that make discoloration more noticeable.

Avoid using chemical cleaners. Tile is praised for its durability and ease of cleaning, but it’s not indestructible. Harsh chemicals like bleach can cause natural materials to fade, while astringent cleaners may ruin the smooth finish of porcelain tiles after only a few uses. Whenever possible, opt for mild green alternatives such as vinegar and baking soda instead.

Even commercial tile cleaners can take their toll when used frequently, and are usually no more effective than garden variety vinegar, anyway. Never use anything more abrasive than a stiff-bristled brush or kitchen sponge to scrub your tile floors. Doing so may leave behind small scratches in which dirt and mildew can set up for good.

How Maintaining Clean Grout to Clean Ceramic Tile Grout?

Clean up spills right away. Letting cranberry juice or orange juice sit on grout for a few hours is a sure way to get a new stain. As soon as something is spilled on your floor, wipe it up with a wet rag, removing every last trace.

If a stain is left behind, pour a bit of hydrogen peroxide over it. Let it sit for a minute before wiping it away with a clean common marbleb tile cloth. Dry spills can also stain grout if they are left to be ground into the floor. Sweep up coffee grounds, clumps of dirt, and other solids soon after they are dropped.

Treat small stains regularly. To avoid having to do a deep cleaning floor tiles too often, treat small stains as they come. Use the same cleaning solution you would use for a deep cleaning, but employ a spray bottle to treat the small area you want to clean. You could also try an alternative small stain-cleaning methods:

Use a baking soda paste. Mix baking soda with a little water to make a paste, and then rub it into the stained section of grout. Let it sit for a few minutes, then use an old toothbrush to scrub it away.

Use white toothpaste. Squirt some toothpaste directly onto the grout in question, then rub it in using your rustic tiles finger. After a few minutes, use an old toothbrush to scrub the area. Wipe it up with a clean wet rag.

Use a pencil eraser. For the smallest stains, a pencil eraser does a surprisingly good job. Choose an eraser that is white, rather than stained a different color, or you may end dyeing your grout the color of the eraser.