Posts

How Doing General Cleaning and Polishing?

/in /by

Wipe marble tiles surfaces with a wet cloth. Use only warm tap water, as many household cleaners are too harsh for marble tiles counters. Wipe the length of the counter with a wet cloth. Microfiber cloths are best for this if you have them, they’ll give the counter a better scrub without needing to use a household cleaner. If you need to clean your counter more thoroughly, you can use commercial cleaners specifically designed for marble tiles.


For marble tiles floors, passing a dust mop on the surface regularly should be enough for regular cleaning. However, if the floor is dirty and requires some extra cleaning, add a couple of drops of dish soap to a bucket of water and use a microfiber head mop to clean the floor with this solution. Dry the floor thoroughly after cleaning it. This kind of cleaning should be done daily to clear crumbs or any dust that may have accumulated on the counter, it won’t clean serious stains.


Wipe tiles dry with a separate cloth. Don’t let the marble tiles just air dry, since marble tiles is easily marked by water spots. Use a microfiber cloth to wipe tiles until they’re dry. Spread a baking soda mixture over the marble tiles polish it. Mix three tablespoons (44ml) of baking soda with one quart (946ml) of water. Use a shammy to spread this mixture over your marble tiles surface.


Let the mixture sit on your marble tiles for a few hours before wiping it away with a wet cloth. Sprinkle crushed chalk over your marble tiles to polish it further. For best results, you’ll want to use a box of white chalk and use a mortar and pestle to crush it into fine dust. Use a shammy to wipe the counter in circles, buffing it and bringing out the shine.


Wipe the chalk dust away with a dry cloth after buffing it. Remove the painter’s tape after applying the silicone adhesive and before it dries. Start removing each piece of tape immediately after applying your adhesive beads. Either remove your tape after each bead or all at once after applying all of the beads.

How Cleaning Bathroom Grout With Stronger Products?

/in /by


Try oxygen bleach products. This is another name for sodium percarbonate, which is a compound made of hydrogen peroxide and soda crystals.Brand-name products include Clorox, OxiClean, Oxi Magic, and Bio Kleen. Mix the product with water as per the manufacturer’s instructions. Apply to the affected area and let it sit for up to an hour before scrubbing and rinsing.


Be sure to use these products in a well-ventilated area, and avoid contact with your skin. Always wear gloves to use these products. Always spot test commercial products in a small area on your grout to make sure the product won’t discolor, erode, or damage your grout. Don’t use any sort of bleach product on colored grout.


Use a commercial grout cleaner and whitener. There are many cleaners out there that are designed specifically for grout, and most of them can be purchased at hardware stores. Be sure to always follow the manufacturer’s instructions for use, and follow all the safety precautions. Commercial grout cleaners include: Zep, Goo Gone Grout, Outrageous, Tilex Tile and Grout.


Beware of chemical combinations. In case you find one chemical hasn’t worked and you want to try another, be sure to wash the area and wait a couple days before trying something new. Just like hydrogen peroxide and vinegar can combine to form peracetic acid, so too can commercial cleansers mix to form poisonous gasses, caustic liquids, and noxious fumes.


Stain the grout as a last resort. For dirt and stains that just won’t come clean from your grout, there are colorants you can apply to cover the stains and make your grout look like new. The area should be nice and clean, but if not give it a once over with your favorite cleaner and let the area dry overnight.

How Preparing the Backsplash Surface?

/in /by

Turn off the power to your kitchen. Find the electrical panel in your home. It is typically a small, metal panel painted to match your wall. Open the panel, then find the switch for the bathroom or kitchen electrical outlets (wherever you are doing the backsplash). Flick the switches to the off position. Remember to flick the switches back on after you have finished installing the tiles.

 

If your tiles are already on the wall and you wish to cut a hole in them, complete this step, then click here to learn how. Remove any light switch and outlet covers. Use a screwdriver to remove the screws from each cover. Place the covers into separate zippered bags along with their matching screws. Work 1 cover at a time so that you don’t mix or lose the pieces.

You will need to reinstall the light switch and outlet covers after you have finished installing the tiles. Clear and cover the counters. Move anything on the counter that might get in the way, such as coffee makers and toasters. Cover the counter with a plastic sheet to protect it. If you are installing the tiles later, it would be a good idea to mask off counters and cabinets.

This will save you a step. To mask off the counters and cabinets: lay strips of painter’s tape along any counter or cabinet edges that touch the backsplash wall. Mark the center of the wall, then draw a plumb line through it. Find the center of the backsplash wall, and make a like mark with a pencil.

Place a 2-ft (61-cm) level against the mark and orient it vertically. Use the edge of the level as a ruler to draw a vertical line spanning the height of your backsplash. The plumb line will help you lay out your tiles evenly once you go to mount them on the wall. Make sure that the level is straight. The bubble inside the glass tube should be centered between the lines.

What Are The Advantages Of Imitating Marble Tiles?

/in /by

In the past, most of the tiles were mainly made of matt tiles. Now, with the improvement of the technology, the material has changed to polished tiles. The material and process changes make the brick face look more luxurious and the visual effect is better. Tile texture of natural and fresh, color and natural marble can almost fake true.

Natural marble has many shortcomings, it is not only heavy weight, construction is difficult, but also there is a certain radiation, so people will not be laying a large area in the decoration. But imitation marble tiles broke the limits, it is not only easy to cut, and whether it is in art, mosaic, sculpture, and ground applications are aspects of combination.

Natural marble although very beautiful, but the difficulty of maintenance is relatively large, the use of a long time will appear oxidation discoloration. The imitation marble tile is a good way to avoid such problems, it is not only very beautiful, but also with high brightness, low water permeability, no radiation and other advantages, more suitable for indoor public space.

How Do You Match Tile Colors? What Should Be Paid Attention To Tiling?

/in /by

First, ceramic tile color with six rules

1 collocation, dark and light, such as black and white, deep and shallow, dark green and gray collocation can be used.

2, similar color collocation, such as light yellow and deep yellow, black and gray collocation.

3, similar colors match, such as yellow and green, red and purple, red and orange, orange and yellow.

4, cool colors and warm colors, cold and warm color relationship is to rely on contrast, produced by people’s natural life experience, and collocation is also very distinctive.

5, the non-polar color and color collocation, black, white, gold, silver, ash is called non-polar color, they can match any color.

6. Compare the colors, such as red and green, yellow and purple, blue and orange, black and white.

Second, ceramic tile shop notes

1, ceramic tile shop before consumption should be checked, to see the grade, color difference and the samples are consistent, such as confirmation, so that the construction leader sign, or notify ceramic tile vendors immediately.

2, if the wall is putty wall or press cement wall, must first root out, do roughening treatment. Wall tiles must not be smaller than 1/3 blocks.

3, the ground should be fully wet, and the horizontal line on the wall and placed on the ground pre row, to ensure that each room on the same level of low brick.

4, floor tiles with good “dry shop” method.

5, bathroom tiles should be good, about 1% of the gradient, and below the floor tiles about 10mm. Kitchen tiles should be appropriate to reduce the slope.

6, in case of yang angle, should use 45 degrees cutting angle processing, waist line of the lower edge should be the window of the upper edge.

7, brick paving after 3-5 days before drilling construction, “laying tiles on the day after the re construction.