Posts

How to Clean Carrara Marble Tiles?

/in /by

Carrara marble tiles is a white marble tiles quarried in the Carrara region of Italy. It is prized for its white appearance and high quality. Like other marble tiless, Carrara marble tiles needs to be taken care of and cleaned in a special way. This is because a wide variety of products can damage the marble tiles or transform its appearance.


Ultimately, though, by performing routine cleaning, removing stains, and taking steps to safeguard the marble tiles, you’ll be better prepared to care for Carrara marble tiles. Apply a diluted bleach solution to specific spots if discoloring remains. You can use a solution of 1 part bleach to 3 parts water on sandstone tiles surfaces but it should be used sparingly.


Simply make the solution and them use a rag to blot it onto the sandstone tiles in areas that are severely discolored. Let it sit for up to 30 minutes and then scrub the area with a soft brush and rinse it with clean water. Using cleaners on your sandstone tiles can take off the protective layer that the material naturally builds up on the surface. This will lead to faster decay over time.


Rinse the sandstone tiles with water after scrubbing it. Use your hose to remove any dirt and debris that you dislodged while you were cleaning. This will also remove any soap or bleach, if you used them. Once your sandstone tiles it sprayed down, it should look much better than when you started. In some cases, you will have to do several rinses to identify areas that you need to continue scrubbing.


Simply go back over areas with your scrub brush that don’t look clean enough. When the surface is completely free of poultice remnants, dry it with another clean nonabrasive cloth. Wring out the excess. Rub the stain in a gentle counterclockwise motion until it vanishes. This will work for spills and circular marks from glasses and goblets. Use a clean nonabrasive cloth to dry the area.

How Using Vinegar and Ammonia to Clean Ceramic Tile Grout?

/in /by

Do a preliminary clean. Before you get down to the deep cleaning methods, it is necessary to do a regular clean up of your rustic tile. Follow your regular cleaning process of wiping down counters or sweeping and mopping floors. This will get all the top layer of scum off, and make your work a bit easier.

Create your solution. In a bucket or large bowl, mix 7 cups of warm water, 1/2 cup of baking soda, 1/3 cup of ammonia, and 1/4 cup of white vinegar. Allow all the ingredients to mix completely, so the baking soda is dissolved. Pour the mixture in a spray bottle. Keeping this in a spray bottle will make it easy to mist the dirtiest areas specifically, and for storage. Fill your spray bottle completely, and then shake the solution well.

Spray the grout. Start on a small area, only as large as 1-2 square feet total. Spray your cleaning solution over the grout so it is dampened. Allow the mixture to set for 3-5 minutes to work into the grout. Begin scrubbing. Use a scrubbing brush of your choice – a hard bristled cleaning brush, a toothbrush, or a magic eraser are all good options. Put some hard work into your scrubbing to get the ground-in dirt out from between your wood tiles.

Interior of a new modern apartment in scandinavian style with kitchen and living room

Clean up the dirty liquid. All your scrubbing has probably created little pools of dirty liquid on your tiles. Use a damp cloth to wipe this up, and wring it out into a separate container. This will keep your polished tiles cleaner in the end. Complete your grout cleaning. Use the above process to move onto the rest of your grout, giving all it a thorough cleaning. Focus on simply getting the dirt and dark areas out of your grout, exposing the natural white underneath.

Do a final wipe-down. When you are convinced your grout cleaning is finished, do a second clean up of the entire area. If you were working on counters or in a bathroom, use a generic cleaning spray and rag to wipe down your marble tiles. For floors, go ahead, mop your tiles again, and towel dry.

How to Fixing Grout Seams The Tiles Cracking?

/in /by

Remove cracked or crumbling grout. If there are cracks in the grout, water can seep in and start damaging the subflooring, loosen tiles design, and even promote mold growth. Minimizing these cracks and repairing cracks that are there are critical steps to take to minimize tile cracking. Scrape out the damaged grout and clean the seam. Remove pieces of the old grout and other bits of material and dirt.

Mix new grout. Mix a small amount of new grout according to the manufacturer’s instructions. The grout should be a pudding-like consistency. Too much or too little water in the mix will prevent the grout from functioning effectively, leading to loose element tiles and opportunities for water leakage. If you need to add water, squeeze in a little at a time from a sponge.

There are different kinds of grout for different applications. There are grouts with urethane and epoxy mixed in, but most homes will use cement grout. If the joints between common marble tiles are less than 1⁄8 in (0.32 cm), use grout without sand. Joints that are larger than this can use sanded grout.

Pack grout around the tiles. Use a rubber float held at a 45-degree angle to the floor to push the grout into the spaces between the ceramic tiles. Make sure there are no small holes or cracks along the edge of the tile. Use your finger to scrape off excess grout and make the new grout level with the grout surrounding it. Work from the edges of the room toward the center so you don’t accidently box yourself in.

Clean up excess grout with a sponge and warm, soapy water. Wait 20-30 minutes for the grout to start setting. It should be firm to the touch. Then wipe away grout left on the tile with a wet sponge, taking care not to pull grout out from between the glazed rustic tiles. You’ll probably have to clean up dried grout on the tiles after the grout has set. Use a dry towel to clean the kitchen tiles, as a wet cloth will only continue to spread around particles of grout.

Apply a coating of grout sealer after the grout is dry. Grout sealer comes in a small can and can be applied with a small foam brush. Pour some of the sealer into a cup and use the brush to trace the grout with sealer. Clean up any sealer that gets on the wood tiles within a few minutes.

How to Clean a Stone Tile Shower?

/in /by

Caring for the stone tile in your shower will preserve its appearance and maintain its condition. Proper care can keep your stone looking like-new for generations. Clean most kinds of dirtiness from your cement tile with a mild detergent, a soft cloth, and a soft bristle brush. Remove stains from ceramic tile by identifying the kind of stain and using the right kind of treatment, like ammonia for oil based stains. Maintain your element tile by avoiding acidic and abrasive cleaners and by removing excess moisture from the stone after every shower.

For severe stains, you may have to reapply the poultice a few times before it is fully removed. Some stains may take five applications or more. Stain removing poultices can be purchased from your local hardware store or home center. Look for it among stone care products.

Some kinds of poultice are sold as pre-made strips of treated paper. These are generally applied to stains similarly to paste poultices.

Buff out water spots and rings with 0000 steel wool as necessary. Hard water can leave rings, a white film, or scale on your stone. When the stone is dry, buff the surface in a circular motion with a dry piece of 0000 rated steel wool. Wipe the surface with a clean, dry, soft cloth or rag after. Use light to moderate pressure when buffing your countertop. Too much pressure may harm the appearance of your stone.

Hire a professional to deep-clean your spots tile. Professional cleaners have special tools and techniques that can extract dirt or grime that may have impacted the pores of the stone, which causes dullness. Have your rustic tile cleaned by a professional when thorough cleaning fails to restore the stone’s luster.

Persistent stains or blemishes that are difficult to treat may require an expert. Call a stone care professional, installer, or restoration specialist to treat problems like these.