Posts

How to Clean Carrara Marble Tiles?

/in /by

Carrara marble tiles is a white marble tiles quarried in the Carrara region of Italy. It is prized for its white appearance and high quality. Like other marble tiless, Carrara marble tiles needs to be taken care of and cleaned in a special way. This is because a wide variety of products can damage the marble tiles or transform its appearance.


Ultimately, though, by performing routine cleaning, removing stains, and taking steps to safeguard the marble tiles, you’ll be better prepared to care for Carrara marble tiles. Apply a diluted bleach solution to specific spots if discoloring remains. You can use a solution of 1 part bleach to 3 parts water on sandstone tiles surfaces but it should be used sparingly.


Simply make the solution and them use a rag to blot it onto the sandstone tiles in areas that are severely discolored. Let it sit for up to 30 minutes and then scrub the area with a soft brush and rinse it with clean water. Using cleaners on your sandstone tiles can take off the protective layer that the material naturally builds up on the surface. This will lead to faster decay over time.


Rinse the sandstone tiles with water after scrubbing it. Use your hose to remove any dirt and debris that you dislodged while you were cleaning. This will also remove any soap or bleach, if you used them. Once your sandstone tiles it sprayed down, it should look much better than when you started. In some cases, you will have to do several rinses to identify areas that you need to continue scrubbing.


Simply go back over areas with your scrub brush that don’t look clean enough. When the surface is completely free of poultice remnants, dry it with another clean nonabrasive cloth. Wring out the excess. Rub the stain in a gentle counterclockwise motion until it vanishes. This will work for spills and circular marks from glasses and goblets. Use a clean nonabrasive cloth to dry the area.

How to Creating a Thicker Subfloor to Stop Floor Tiles from Cracking?

/in /by

Get 5⁄8 in (1.6 cm) or 3⁄4 in (1.9 cm) thick sheets of plywood. tiles design usually employ half-inch thick plywood as part of the tile. However, to minimize flexion of the wood tile – which in turn can cause cracking in Santana Stone tiles – you can use thicker plywood. A layer of cement board over the plywood will make the tropical tile even firmer. Thicker sheets of plywood make for reduced expansion and contraction of the super white tile due to humidity or cold.

Plan out how the plywood is going to sit on the joists. You’ll want the grain of the plywood to run perpendicular to the joists, as grain running with the joists makes for a weaker clunny tile. The plywood should also be staggered so that the edges of each row do not overlap, which will likewise strengthen your spots tile and minimize movement.

Use a chalk line to ensure that the plywood is laid straight. A sheet of plywood is 4 ft (1.2 m) or 3⁄4 in (1.9 cm), so measure from the wall and make a mark on each joist at that length as a guideline for the sheets of plywood. Plywood set at even a slight angle will throw off the rest of the panels.

Add blocking along the edges of where the plywood is going to lie. The edges of sheets of plywood should be supported so they do not cave in. Once you have laid out where the plywood is going to go, cut blocking to go along the perimeter of each piece where it is not supported by a joist.

Use adhesive to secure the plywood to the joists. Before putting down the plywood, use a caulk gun to squeeze an adhesive such as Liquid Nails onto the joists underneath where the plywood is going to be laid down. This adds for an extra layer of protection against movement. Cut the tip off the tube of adhesive to allow a bead about a half an inch wide.

Put down one sheet of plywood at a time and leave a 1/8 inch gap in between each sheet. Makes sure each side is aligned with the marks you made has room to expand with the heat. Experts recommend leaving a 1/8 inch gap on all side of the plywood. Once the sheet is in place, pound a nail ¾ of the way in on each corner. This will keep the sheet in place but will allow you to easily remove the nail if you need to make adjustments.