Posts

How Removing Deep Stains?

/in /by


Mix 1 part baking soda with three parts water. Combine the baking soda with the water in a small bowl or cup. Continue to mix it together until the baking soda absorbs the water and forms a paste. If your paste is too thick, add more water to it. If the paste is too runny, add more baking soda.


Apply the paste to the stains. Wear gloves and use your hands to smear a good portion of the paste over the stains on your shower. Target any discoloration or built up mildew that you weren’t able to remove from a basic cleaning. Cover the paste with plastic wrap. Tape the ends of the plastic wrap so it stays in place. Don’t cover all the edges in tape so that the marble tiles can breathe.


Let the paste sit on your shower for 24 hours. The paste will dry and absorb the stain under it. When the paste is ready, it should be dry and hard. Remind people in the house that you are doing a deep cleaning and that they won’t be able to use the shower. Rinse and wipe down the baking soda.


Remove the baking soda paste from your shower by rinsing down your shower and wiping the stained areas with a rag. If you notice that the stain is still visible, repeat the steps until it is fully removed. Dry the shower. Use an absorbent rag or squeegee to dry off your shower completely.


You should dry down your shower after every use, but doing a more extensive cleaning with a mild dish soap and water two to three times a week should keep the marble tiles looking clean and fresh. Rinse the shower. Use a showerhead or a bucket of water to rinse the entirety of the shower down, including the walls. It’s important that you remove any leftover soap or it may sink into the marble tiles and create stains later.

The Knowledge of Cover Exterior Cinder Block Walls

/in /by


Place vertical boards along the wall to connect the strips. Cut more furring strips to the size you used previously. Line these boards up with the edges of the wall, chalking straight guidelines as needed for the installation. Drill and screw these boards to the cinder blocks. Apply more vertical strips about every 16 in (41 cm) to create a framework for the vinyl siding.


Remember to install vertical boards around each door and window to complete the furring “frame.” These components need to be framed in order to waterproof them properly. Measure and cut the vinyl to fit evenly over the wall. Run a tape measure from the top edge of the upper furring strip to the bottom of the lower one. Add an extra 1⁄2 in (1.3 cm) to your measurement to account for overlap.


Then, cut the vinyl panels evenly to fit over the height of the wall. Use a circular saw with a plywood-cutting blade to trim the panels. Remember to wear goggles, earmuffs, and a dust mask to keep yourself safe while operating a saw. Attach a vinyl starter strip below the bottom furring. The starter strip is a slotted piece of trim used to hold the vinyl to the furring board.


Position it so it extends about 1⁄4 in (0.64 cm) below the lower furring. Place 1⁄4 in (0.64 cm) galvanized siding nails in the slots pre-cut in the starter to pin it in place. Look for vinyl siding kits online or at your local home improvement store to get all the components you need. Alternatively, buy the parts separately to suit your wall.


If you’re working around doors and windows, get more vinyl starters. You need corner pieces and J-channel pieces to connect them together. They attach to the furring boards the same way the starter does. Lay vinyl panels from the bottom of the wall to the top. Position the first row of vinyl panels over the starter strip on the bottom of the wall.

How Doing Routine Cleaning For Granite Tiles?

/in /by

Wipe the area with a dry mop or duster. Before you begin cleaning your granite tile, it is important to remove surface dirt. Doing this will keep any bits of grit or grout from scratching your granite, which can trap bits of dirt deep in the stone and dull its finish.

Use warm distilled water and mild dish soap. If your granite is just a little dirty, first try cleaning it with warm distilled water and some mild dish soap. Dilute a few drops of the soap in a bucket of water, wringing a soft cloth to remove excess water before each wipe of the granite tile. Standing water can stain granite if left too long.

Avoid soaps with lots of dyes and fragrances. Dyes can stain light colored granite. Microfiber cloths you can buy at the hardware store specifically designed for stone are best. Don’t ever use anything abrasive such as scrubbing sponges or steel wool to clean granite. Though the stone is durable, it is vulnerable to scratching.

Work in a methodical way so you don’t miss any spots. For example, you could clean all the tiles left to right in one row before moving to the next. If your granite tiles are on the floor, be sure not to clean yourself into a corner.

Dry the granite thoroughly to avoid water spots. Use circular motions to dry, as if buffing a car. If you don’t have a soft cloth, you can use an old T-shirt without screen prints.

Introduction Decoration Choose Wood Floor Or Tile

/in /by

A few reasons why we love wood flooring

Natural wood gives a natural sense of texture, comfort and beauty, and has the advantages of so-called “upper grade”. If the room with wooden floor, not only comfortable, but also can greatly reduce the impact of sound on the floor of the room warm and quiet.

Wood floors are more “gentle”, and if there is an old man and a child falling down, it is not easy to walk. It will cause great harm, but if it is tile, it will fall more serious.

Wood floor defects

The wood floor is nice, but it needs more care. The wooden floor is influenced by the weather and moderate flooding effect, easy deformation curl up; need to wax regularly maintenance; easy to be sharp objects; composite wood flooring and formaldehyde release; compared to the shorter life of wooden floor tiles.

Two, preference tile reason

Now tile obvious advantages are: easy maintenance, simple maintenance, not easy to hide, no air pollutants, long service life, generally will not be scratched, and so on. If you’re more comfortable, choose the magnetic ring. Tile size, color is also very rich, decorative effect and wooden floor effect comparable, easy to care, just sweep, wipe clean.

Several defects of ceramic tile

Comfort is poor, tile cold, foot feels stiff, not warm; poor insulation insulation; ceramic tile paving complex and fussy construction; in the wet season is easy to slip.
Can be used in accordance with the requirements of different regions, the use of both, such as kitchen, bathroom are tiled walls, bedroom, living room, floor wood flooring, to play both advantages.
Do you have the answer to the choice of flooring? Whether it’s wood floor or tile floor, the right one is the best. You can choose according to your actual situation.