Posts

How to Cut Tile Backsplash?

/in /by

Installing a tile backsplash yourself is a great way to save money while getting the exact look you want. There is more to installing backsplashes than just arranging tiles, however; you have to measure and cut the tiles so that they fit properly. If the backsplash is already installed, you may still be able to cut holes into it for new fixtures, as long as you use the proper tools.

Use tile nippers for small tiles. Tiles that are smaller than 1 or 2 inches (2.5 or 5.1 cm) may be difficult to cut on a score-and-snap tile cutter. Not only could you hurt yourself, but you could break the tile. Instead, use a pair of tile nippers to pinch the tile where you need to break it. You can use tile nippers on larger tiles to “cut” curves.

Use a wet saw to notch tiles, if needed. Sometimes, the corner of a cabinet or outlet cover will extend into your backsplash tiles. Measure the corner, then trace it onto the tile with a pencil or marker. Place the tile onto the sliding table of the wet saw. Gently guide the tile into the saw to make the first cut. Pull the tile back, then create the second cut. Use a tile nipper to break off the piece between the 2 cuts.

Install the tile sheet using your preferred tile cement. Spread the tile cement across the backsplash area, then press the tile sheet into place. If you cut your tile sheet smaller, arrange it so that the gaps caused by the size difference are along the top edge, where the cabinets are. If there is a gap along 1 of the side edges, position the sheet so that the gap is in a corner.

Measure the excess tiles against the gaps. You should still have some tile sheeting left over from when you cut the tile sheet down. Take these excess tiles, and measure them against the gaps. If you need to, mark the back of each time with a pencil or marker to figure out how much you need to trim.

How to Make Ceramic Tiles?

/in /by

Ceramic tile can be a beautiful addition to your home or garden. It begins with just a lump of clay, which is mixed with other ingredients to create a medium by which to form the tiles. Pigments and designs are added before glazing to add color and texture. If you love working with your hands, making your own ceramic tile can be fun and rewarding, especially if you intend to use it in your own home or garden. Aside from purchasing a kiln for firing your tiles, most ingredients are fairly inexpensive and some can be made from materials in your own home. Making ceramic tiles takes only a bit of creativity and time.

Begin with good clay, such as that designed for sculpting and that has small- and large-sized grog (fired and ground up clay). Check the temperature at which you will fire the clay. Ensure that the clay you use will mature at that temperature. Work the clay when it is fairly dry. Ensure that your wood tiles are at least 1/2-inch (1.3 cm) thick.

Roll a slab of clay onto a hard working surface from which your clay can be easily removed. Use a slab roller to flatten the clay. Calculate the diameter of a ball of clay that is needed to reach your marble tile’s size, including shrinkage. Use a magic marker to mark that size on your bat. Throw to the mark.

Determine the weight of the clay ball that ended up to be the correct dimensions of your floor tiles and use that weight for the rest of the clay. Construct a bottomless wood frame. Pound the clay into the frame. Cut off the excess clay. Allow the clay to dry slightly or use a spray lubricant to avoid having it stick to the wooden frame. Push the clay out of the frame’s bottom using a strong material the same size as the clay.

Purchase a clay-cutting device, which is similar to a cheese slicer, or make your own. Ensure that the device is at the specific thickness for your tile specifications. Put the device wire evenly through the block of plugged clay (ground clay that is kneaded with water and becomes more elasticized) to slice off bathroom tile pieces.


Make a metal or wooden template. Cut the cement tiles out after the clay has dried to a leathery consistency. Cover the tiles with plastic. Place the tiles between two pieces of sheetrock, plywood or fire-proofing board to help draw out the moisture or dry the tiles on a wire rack or plastic grids.

Incise a slab of clay with a 3.94-inch-long (100 mm) line. Fire the slab at the appropriate temperature. Measure the line after firing to determine shrinkage rate. Stack your kitchen tiles atop each other or place the tiles in a tile setter for bisque firing or place topps tiles on a flat surface for glaze firing. Create a moat to protect your tiles and ensure even firing using bars of clay.

How To Maintain Tile?

/in /by

As we all know, in the Home Furnishing life, ceramic tile is very important, however, there will be wear and tear, discoloration and other common problems in the use of a long time, especially the bathroom tiles, because the bathroom itself environment is more humid, so it is more serious, which requires us to pay attention to the maintenance of ceramic tile the details in life!

There is also a convenient and environmentally friendly way to clean your body, using white vinegar and lemon peel. Clean the dirt on the surface of the sanitary ware first, then dip the soft cloth on a little white vinegar to wipe the surface of the sanitary ware or wipe with the lemon peel. Only a little while, the sanitary ware will be shining as new, and the fragrance will be sent out.