Posts

How Sealing Your marble tiles Shower?

/in /by

Test to see if your shower needs to be sealed. Unless you have a white marble tiles shower, you should not seal your shower. You should also not seal your shower if there is already an existing seal on it. Test to see if there is sealer by putting a couple of drops of water onto the surface of the shower and allowing the water to dry for ten minutes.


If the area is dark, it means that your marble tiles has absorbed the water and most likely needs to be sealed again. If the sealer has pooled on top of your marble tiles, it means that it’s already sealed. If your shower is already sealed, there’s no reason to do it again, and it can actually be detrimental to your marble tiles.


Dust and clean the inside of your shower with a damp rag. The first step before you seal your shower is to make sure that all the dust and dirt that may be built up is removed before you seal it in. Wipe down your shower with a damp rag and water, then dry it with a clean rag. Make sure that your shower is dry and free of dirt before you start sealing.


Spray down your shower with the sealer and wipe it in. Spray down your shower with the sealer and use a sponge or a rag to wipe the sealer in. Work your way from the top of the shower to the bottom of the shower and try to apply even coats throughout it. Some popular brands of marble tiles sealer include DuPont Stone Sealer and Miracle Sealants.


It’s important that you get a stone sealer made for a stone like marble tiles. Allow the sealer to soak for 15 minutes. During this period the sealer will be absorbed by the marble tiles. You should start to see the marble tiles turn a darker color as it absorbs the sealer. Wipe off excess sealer on the surface of your shower. Use a dry absorbent cloth to remove any excess sealer that pools on the top of your shower.

The Knowledge of Cover Exterior Cinder Block Walls

/in /by


Place vertical boards along the wall to connect the strips. Cut more furring strips to the size you used previously. Line these boards up with the edges of the wall, chalking straight guidelines as needed for the installation. Drill and screw these boards to the cinder blocks. Apply more vertical strips about every 16 in (41 cm) to create a framework for the vinyl siding.


Remember to install vertical boards around each door and window to complete the furring “frame.” These components need to be framed in order to waterproof them properly. Measure and cut the vinyl to fit evenly over the wall. Run a tape measure from the top edge of the upper furring strip to the bottom of the lower one. Add an extra 1⁄2 in (1.3 cm) to your measurement to account for overlap.


Then, cut the vinyl panels evenly to fit over the height of the wall. Use a circular saw with a plywood-cutting blade to trim the panels. Remember to wear goggles, earmuffs, and a dust mask to keep yourself safe while operating a saw. Attach a vinyl starter strip below the bottom furring. The starter strip is a slotted piece of trim used to hold the vinyl to the furring board.


Position it so it extends about 1⁄4 in (0.64 cm) below the lower furring. Place 1⁄4 in (0.64 cm) galvanized siding nails in the slots pre-cut in the starter to pin it in place. Look for vinyl siding kits online or at your local home improvement store to get all the components you need. Alternatively, buy the parts separately to suit your wall.


If you’re working around doors and windows, get more vinyl starters. You need corner pieces and J-channel pieces to connect them together. They attach to the furring boards the same way the starter does. Lay vinyl panels from the bottom of the wall to the top. Position the first row of vinyl panels over the starter strip on the bottom of the wall.

How Laying the Tiles?

/in /by


Mark your tile layout on the substrate and mark out your first course carefully. If your shower enclosure walls are not perfectly square, or if you plan to install accent tiles, the layout of these tiles becomes increasingly important. Measure up from the bottom of the backer board the height of a tile minus 1/2″. This will give you a 1/2″ overlap over the tile lip on your shower pan.


Make sure that you allow room for the grout joints as well. Mark this with a sharpie or chalk and using a level, transfer the mark across the shower stall. This will be a guide for the top of the first row so that all tiles will be level. Only use dry tiles make sure that the lay out works as well.


Another way to plan out the first row of tiles is to measure the high part and low part of the shower pan. Make the cut spot on the low end a full tile, mark it, and then cut the tiles on the high side down to the level of the uncut tile on the low side. Keeping grout lines away from the inside corners of the enclosure can prevent the need for tiny tiles and poor grout joints. Plan accordingly and always make cuts tight on the inside corner.


Mix enough thin-set for the bottom row. You want your thin-set to be the consistency of peanut butter — not too thick or it will dry out and not too thin or you’ll have a hard time setting the mortar with strength and cleaning. Use an electric drill and a mortar mixing bit attached to your drill to mix your thin-set mortar. This will ensure even consistency and ultimately a better product. Let the mortar set for seven minutes and then mix it again.


Dampen the cement board with a sponge before applying the mortar. If you do not, the cement board will draw the moisture out of the thin-set too quickly, making for a brittle set that is susceptible to cracking.

How Cleaning Polished/Glazed Porcelain Tiles?

/in /by

Sweep the floor with a dust mop. Start by sweeping the floor to remove any dust on the porcelain tiles. You can use a dry dust mop or a vacuum. You can also use a microfiber mop, as it will be gentle on the tiles. Brooms with straw or plastic bristles will be too harsh on the floor and could scratch the tiles. Make sure you sweep in the corners and between tiles. You want to try to remove as much surface dust on the tiles as you can before you move on to more intense cleaning.

Use a soft, nylon brush to remove any dirt. You can use a nylon cleaning brush or an old toothbrush to remove any dirt or dark spots on the floor. Wet the floor with hot water and use the brush to remove surface dirt. Scrub the tile in a circular motion, making sure the tile is damp when you scrub it. Do not scrub any tiles that are dry, as this could scratch the tile.

Apply a cleaning solution for stains. If you notice any stains on your polished or glazed porcelain tiles, you should apply a cleaning solution using a mop. You can use a home solution of white vinegar and water or a professional cleaning solution. Make a home solution by combining ¼ cup white vinegar with two gallons of warm water. Mop the floor and let it sit for five to ten minutes. Then, mop the floor again, rinsing off the solution. The vinegar will help to disinfect, deodorize, and clean the tiles.

For a professional option, use a cleaning solution from your local home hardware store or the cleaning supplies aisle. You should make sure the solution is safe for use on glazed or polished tile before you use it. You may want to do a spot test by using a small amount of the solution on the floor to ensure it does not damage the floor.

If there are coffee stains on the tiles, you can use baking soda to remove them. Apply a sprinkle of baking soda on the stain and then dampen it with a clean cloth. Gently scrub the area until the stain is removed.

Introduction: Master Living Room Tiles Raiders Home Life More Enjoyable

/in /by

Living room skirting board

Simplicity and fluency are forever themes. The concept of metaphysics and parquet are outdated superfluous. The skirting line is to be done, because the general wall paint, and paint and ground connecting parts often with the living room furniture feet and foot contact, easy to get dirty and damaged, and the use of a baseboard with tiles made to avoid this problem, and make the room more beautiful. The upper end of the foot line shall be ground to 1/4 or 45 degrees, and the machined surface shall be polished.

Tile color selection

Indoor requirements are spacious and bright, so that people feel relaxed and comfortable. So the light is appropriate, such as white, beige, color or pattern can be slightly, to high health requirements for the master, select solid color can better reflect the owner’s elegant, but to spend more time and energy, because the pure dirty, need frequent cleaning, for those busy, willing to spare time on the Internet, sleep and other aspects of the owners, the best choice with patterns or particles of ceramic tile.

Selection of tile material

Choose vitrified stone is better, because it is wear-resisting, bright, easy to clean. Some people like to use antique brick, antique brick color rich, reflecting the personality, but the color is often heavier, cleaning is also a certain degree of difficulty. Stone is best not used, because not only the high cost of stone, the color of a single, but most of the stone radioactive, surface finish and abrasion resistance is also very low. They are often used in large public places.

Selection of polished tiles

If the living room area of more than 30 square meters, 80*80 should be less than the brick, area under 60*60 standards, but not less than 40*40. Large size can make the room spacious and spacious, with a wide view. But the large size tiles if the shop is stuck in a small area on the ground, will make the size of the room collocation uncoordinated, like a man wearing an oversized clothes, on the other hand, if a large area of paving the small ceramic tiles, will appear crowded indoor complex.

How to choose the wall ceramic tile for toilet?

/in /by

1.Choose ceramic tile that absorbs low water rate
Generally speaking, the ceramic tile with high quality, the absorption rate is very low, this can dry very quickly. If ceramic tile not indicate the bibulous rate, can use a tea or water droplets in the back of the ceramic tile, minutes after inspecting the diffusion degree drops, the less water absorption, it indicates that the bibulous rate is low, the quality is better. Bibulous rate is high after heat bilges cold shrink can cause cracks on the surface of the ceramic tile ceramic tile and the whole piece of floor tile of wall of spalling, decorate toilet clear four seasons of the northern region, more should pay attention to this problem.


2.Choose high-density tile texture
When shopping for ceramic tile, can see whether the brick face is flat from the side, whether the needle hole that appears thick and uneven. At the same time, can knock ceramic tile to listen to sound whether the sound is clear, the sound is more brittle, the texture density of ceramic tile is high, hardness is better. This kind of ceramic tile is laid to defend bath space, not easily damaged, also facilitate maintenance cleanness. Generally speaking, this actually also has little hard requirement, as long as waterproof is good, the glaze foot, choose a suit that suits your home to defend bath color to be able. The light is good, can use a little dark brick, but if the light is not good, suggest only use light color, relatively inferior smooth brick, don’t look too cold, suggest don’t use the highlights.