Posts

How Using a tiles Poultice?

/in /by

Purchase a stone poultice. This is a fine powdered substance that you can find in most home improvement stores. It’s designed to pull stains out of quartz and other stone surfaces. Make sure the product is non-acidic. Mix with water. Scoop about a cup (0.95 metric cups) of powder into a clean bowl or plastic container.


Gradually add water until you have a substance as thick as peanut butter. Mix as you add the water. Wet the stained area. Use a clean nonabrasive cloth. Moisten it with warm water. Lay the cloth on the stain immediately before you’re ready to apply the poultice. Apply the poultice to the stain. Get a blunt plastic scraper.


Use it to gradually scoop out the substance and lay it on the stain. Keep doing this until the poultice is about 0.25 inches (0.64 cm) to 0.5 inches (1.3 cm) high. Cover the poultice. Lay plastic over the poultice. This could be cling film or an old plastic bag cut into smaller pieces. Secure the plastic with painter’s tape. Let it sit for 24 hours.


Let the poultice air dry. After 24 hours, the poultice will be partially to half dry. Remove the plastic. Then, allow the poultice to finish drying. This will take about another 24 hours. Remove the dry poultice. If the poultice hasn’t dried after 48 hours, check it every hour or so until it is completely dry.


When it feels hard to the touch, gently remove it with a plastic scraper. Insert the scraper under the poultice and push forward. Keep doing this until you’ve completely removed the poultice. Rinse and dry the area. Moisten a clean nonabrasive cloth with warm water. Rub the affected area in a gentle counterclockwise motion.

How Ensuring a Safe Cleaning?

/in /by


Avoid harsh cleaners and anything abrasive. Some cleaners may strip your marble tiles of its finish. Check the label of all cleaners to ensure they are suitable for marble tiles. Abrasives in cleaners and abrasive cleaning tools, like scouring pads, steel wool, or scrubbers, can also cause damage to the marble tiles. The surfaces cleaners are intended for should be clearly marked on the label. Abrasives, too, are generally marked on the label.


Test cleaning products on an out of view part of the marble tiles. Even if the label says a cleaning product is suited for marble tiles, it’s always a good idea to test the cleaner first. Choose an out of sight location on the marble tiles, like under a stationary appliance, and use a small amount of cleaner on the marble tiles. If the finish or color is affected by the cleaner after it dries, refrain from using the cleaner.


Soak stubborn stains in bleach. Although bleach is a generally accepted cleaning agent for marble tiles, it’s relatively harsh. Only use bleach sparingly to clean your marble tiles. Same as when using vinegar or hydrogen peroxide, dampen a clean, soft rag with bleach, wring out excess, and drape the rag over stains. Only use this technique for marble tiles that is light in color. Bleach may cause discoloration in dark colored pieces.


Identify engrained stains in your marble tiles. If you’ve cleaned a spot time and again with various cleaners, it’s likely the stain you are attempting to clean is engrained in the marble tiles. To remove spots like this, the marble tiles will have to be buffed and refinished. For the best results, this should only be attempted by a professional.


Apply the cleaning solution with a clean, soft rag. Douse your rag in the heavy-duty cleaning solution. Wring out excess solution over the sink, then lay the saturated rag on the stains. Wait roughly 10 minutes for the stain fighting action of the solution to go to work, then wipe away remaining liquid with a clean, dry, soft rag.

The Knowledge of Tile Wood Glues

/in /by


Wipe away the excess glue. Use a damp rag to blot at the glue squeezing up through the cracks in the newly-repaired gap, then go over the seam until no residue remains. Any adhesive left behind by mistake could dry to a rough texture underfoot or produce mild discoloration in the laminate.


If you used caulk or wood putty to fill the gap, you may need to sand down the excess material once it has had time to dry. For the smoothest finish, use 180-grit sandpaper or higher. Most wood glues dry clear, which means they won’t be visible in the seam between the two planks.


If there are a large number of patches on your floor, or there’s a noticeable difference in level of sheen, you might need to re-varnish the entire floor. Wipe down tiles. After the grout has completely dried, clean it off again with a dry cloth. Seal your tiles. If you want, you can apply a grout sealant to help protect your tiles.


Add a small line of silicone caulk to the bottom edge of your tile to seal out water and prevent mildew growth. Sprinkle over a little turpentine and white spirit. This will create patchy streaks on the dark paint of the squares. Leave the dark squares to dry. Remove the paper from the border. Paint entirely in black paint. While it is still wet, use a paint cloth to wipe turpentine in it here and there, to create a mottled effect.


Don’t do all of the border, just parts to give the effect of old marbling. Use a fine brush to add very thin faux white lines to the border. Only do this part once the paint has dried. Remove the paper from the entire floor. Seal the floor with five thin coats of a low-gloss polyurethane varnish. Allow each layer to dry before adding the next.

How Deep Cleaning the Tile?

/in /by

Pick a pH-neutral cleaner. You don’t want an acidic or basic cleaner for this type of polished tile, so pick a cleaner that states it is pH neutral. You can find special cleaners specifically for quarry floors, if you prefer.

You can also make your own cleaner. Mix 0.5 cups (120 mL) of baking soda into 1 gallon (3.8 l) until the baking soda is completely dissolved. Add 5 drops of liquid dishwashing detergent, and stir gently to combine. Dampen a mop with the mixture. Once again, you don’t want to use a large amount of cleaner or water on this type of floor. Therefore, make sure you wring out the mop well once you’ve dampened it with the cleaner.

Mop the floor. Run the mop over the floor, focusing on particularly dirty spots. Scrubbing is fine on the dirty areas, though you don’t want to use anything too abrasive. Keep in mind that this vatican tile will always have a matte finish. You may need to scrub the grout a bit harder, but it will likely still get darker over time.

Rinse the floor thoroughly. You don’t want to leave cleaner on the floor, as it can damage the tile. Rinse it off with warm water, making sure you get off all the cleaner before moving on. Dry the floor with a dry mop or rag. Once you’ve rinsed the floor, dry it off with a dry mop. You can also use a rag, if you prefer. You just don’t want to leave water on the floor, even to “soak” stains.

Use a clean wet towel and wipe your floors so you can get as much of the leftover splash and residue from the buffing compound off the floors and fixtures. Then go over your wood marble tiles once again with a dry towel. Finally, after your tiles and grout lines are dry, use a stone/marble sealer to seal your calacata tiles. Two coats are sufficient and your floors will look as good as new.

How Deep Cleaning Techniques?

/in /by

Mop the floor with warm water and a vinegar solution. Mix 1/2 cup vinegar with a gallon of water and proceed to mop as usual. If the floor still doesn’t look as clean as you would like, mop the floor again using fresh water and detergent.

Rinse the floor with clean warm water after you are done washing it. It is important to remove all residual soap from the tiles so it doesn’t remain on the floor to attract and hold dirt. Do not use vinegar or chemicals on marble flooring. See How to Clean Marble for information on safely cleaning stone floors.

Remove stains from tile floors. Prepare a paste using a 50/50 mixture of scouring powder and warm water. Rub the paste on the stain using a clean cloth, and then allow it to sit for five to 10 minutes. Scrub the area with a soft brush, then wash the area with warm water and a cloth to remove all remains of the paste. Repeat the process if the stain is still visible. If a spill is left to sit for awhile, it can stain your tile floor.

Clean mildew from tile floors. Prepare a 50/50 solution of water and ammonia. Scrub the area using a soft brush and the ammonia solution. Rinse the floor with clean water after the mildew is gone. Tile floors in bathrooms tend to get mildew sometimes. The best prevention method is to air out the room after you’ve showered and keep the floors dry. If mildew does accumulate, an ammonia solution should take care of it. Put on a pair of rubber gloves to protect your hands. Also, make sure the room is well ventilated.

Remove rust spots from tile floors. Put on a pair of rubber gloves to protect your hands. Dampen a clean cloth with kerosene. Rub the rust stain away using the kerosene rag. Wash the area with warm water to remove residual rust and kerosene, then repeat the process if the rust is not entirely gone. You probably won’t have to do this often, but if you do, cleaning with kerosene does the trick on rust.