Posts

How to Cut Tile Backsplash?

/in /by

Installing a tile backsplash yourself is a great way to save money while getting the exact look you want. There is more to installing backsplashes than just arranging tiles, however; you have to measure and cut the tiles so that they fit properly. If the backsplash is already installed, you may still be able to cut holes into it for new fixtures, as long as you use the proper tools.

Use tile nippers for small tiles. Tiles that are smaller than 1 or 2 inches (2.5 or 5.1 cm) may be difficult to cut on a score-and-snap tile cutter. Not only could you hurt yourself, but you could break the tile. Instead, use a pair of tile nippers to pinch the tile where you need to break it. You can use tile nippers on larger tiles to “cut” curves.

Use a wet saw to notch tiles, if needed. Sometimes, the corner of a cabinet or outlet cover will extend into your backsplash tiles. Measure the corner, then trace it onto the tile with a pencil or marker. Place the tile onto the sliding table of the wet saw. Gently guide the tile into the saw to make the first cut. Pull the tile back, then create the second cut. Use a tile nipper to break off the piece between the 2 cuts.

Install the tile sheet using your preferred tile cement. Spread the tile cement across the backsplash area, then press the tile sheet into place. If you cut your tile sheet smaller, arrange it so that the gaps caused by the size difference are along the top edge, where the cabinets are. If there is a gap along 1 of the side edges, position the sheet so that the gap is in a corner.

Measure the excess tiles against the gaps. You should still have some tile sheeting left over from when you cut the tile sheet down. Take these excess tiles, and measure them against the gaps. If you need to, mark the back of each time with a pencil or marker to figure out how much you need to trim.

How to Using a Glass Cutter for Straight Cut a Ceramic Tiles?

/in /by

The tool you use will depend on what sort of cut you are doing and how many marble tiles you plan on cutting. If you just have to cut a few tiles design, a glass cutter will suffice. If you need to cut more tile, however, a tiling tool or a wet saw might be more convenient.

Use a pencil and a square to measure and mark your floor tile. A square is a special ruler shaped like a right angle. Align the horizontal edge of the square with the bottom edge of the tile. Use the vertical edge of the square and a pencil to draw your guideline. This method is better suited to small jobs where you just need to cut a few small tile. It is not suitable for cutting corners or curves.

Set the tile down onto a sturdy surface and reposition the square. A workbench or plywood would work the best for this. Move the square off to the side so that it is right next to your marked line. This will allow you to cut right along the line without cutting into the square.

Score the tile with the glass cutter. Press down on the bathroom tile with the glass cutter, then drag it across the line that you drew, using the square as a guide. You may have to score the tile a few times in order to make a shallow cut. If you can’t find a glass cutter, try a carbide tipped pencil instead.

Snap the tile over a wire hanger. Place the polished tile on top of a wire hanger. Make sure that the hanger is aligned with the line that you scored. Next, press down on the un-scored edges of the tile until it snaps. if you scored from left-to-right, press down on the top and bottom edges, and vice versa. If you scored the tile close to the edge, snap off the thinner side with tile nippers.

Smooth the edges of the tile with a brick, if needed. You can do this by rubbing the cut edge of the marble tiles design back and forth across a brick or some concrete. This will buff away any roughness, much like sandpaper would on a block of wood.

How To Maintain Waterproof Floor Tile?

/in /by

1, at home free time, most of the women will be cleaning, for the floor, we usually have to clean up, it is best to regularly clean, select the appropriate cleaning agent for removal. Acid and alkali properties of the cleaning agent can effectively remove ceramic tile surface stains, but because of the acid-base composition of ceramic tile surface may cause corrosion, it is not suitable for frequent use. Should use more ph value for the neutral cleaning agent, daily cleaning can be used household cleaning detergent, soap and other cleaning.

2, on the tile, usually in each crevice, the accumulation of dirt and bacteria are the most, so in cleaning and maintenance, need to be particularly careful. Which is the main raw material and white cement putty, so the dirt adhesion of the above it is difficult to clean, in tile paving completed and daily after cleaning, can be in the crevice of a waterproof agent with brush brush, can play the role of waterproof mildew.