Posts

How to Removing Stains With a Stone Tile Shower?

/in /by

Investigate the location of the stain. This can provide useful information for what caused the stain. Certain cement tile stains will need special cleaning procedures to be removed from the stone. Note the color, size, shape, and pattern of the stain, along with anything in the area that might have caused it.

Cleanse oil based tile stains with a household detergent or ammonia. Some common examples of oil based wood tile stains include grease, tar, or cosmetics. These will cause your bathroom tile to darken. To dissolve oil based mosaic tile stains, clean the area by gently wiping it with a soft cloth and a household detergent, like dish soap, or ammonia. Afterwards, dry the area with a soft towel.

If detergent and ammonia fail to remove the stain, try mineral spirits or acetone. Use these sparingly and as a last resort. Flush these cleaners with water after applying, then dry the area. Eliminate mildew and algae with a heavy-duty cleaner. Mix a diluted cleaning solution containing a half cup (237 ml) of ammonia, bleach, or hydrogen peroxide with a gallon (3.8 L) of water. Clean the surface with the solution with a soft cloth, rinse the area well, then dry it with a soft cloth or towel.

Never mix bleach and ammonia. Doing so will create toxic fumes that can result in serious harm or death. Erase organic marble tile stains with hydrogen peroxide and ammonia. The most common kinds of organic casstle tile stains come from bodily fluids, like urine or feces, tobacco, paper, and food. These may create a brown-pink stain. Clean these areas as you would normally with 12% hydrogen peroxide and a couple of drops of ammonia.

In some cases, you may be able to get rid of an organic stain just by removing its source. After removal, wait a few days to see if the stain disappears. Hydrogen peroxide may fade or lighten the color of your stone. Test it on an out of sight location before you use it. Only use this technique occasionally to prevent color loss.

Use a stone poultice for metal wood tile stains. Mix the poultice according to its directions. Usually this will result in a paste that is the consistency of peanut butter. Wet the stain with distilled water. Apply the paste to the stain so it is roughly ¼ to ½ in (.64 to 1.3 cm) thick. The paste should extend beyond the stain by roughly an inch (2.5 cm). Tape plastic over the poultice, wait the time indicated on the label, then remove it according to its directions.

How to spreading adhesive or mastic, and laying tiles?

/in /by

Pick up all tiles design and set aside. On your prepared surface, begin spreading the adhesive with the notched trowel. You will start from the center point, work only in one quadrant, and apply small sections at a time, following the pattern during the rehearsal. Spread adhesive evenly, then using the notched edge, make a raking motion. You should have grooves neither too deep nor too shallow. Set the first marble tiles in place at the corner lines made by the center point. Do not twist kitchen tiles; simply press the tiles down firmly yet softly.

Set tiles price spacer and then continue with additional common marble tiles. (Remember to set wood tiles spacers after each wood marble tiles). Use your level to determine degree of level of the tiles as you go along. (Not all surfaces are perfectly level). If slightly uneven, either manipulate the tiles or add a little more adhesive to the floor until level. Usually, after a quadrant is complete, remove the tiles spacers so they do not set into the adhesive. Follow this process for the remainder of the floor, making sure to check the level as you go along.

Wait. After the polished tiles have been set, it is usually advised to wait at least one day (or overnight) to allow the adhesive to dry, or cure. After the adhesive has cured, you will grout the joints. Continue working in quadrants as before. Using a rubber float, apply only enough grout as you can effectively work with. In a diagonal direction, press grout into the joints to an even level with the bathroom tiles.

Skim excess from cement tiles with the rubber float. You will notice a mild “grout haze” on your tiles. Wait a few minutes for the grout to stiffen up in the joints. Use a damp sponge work across the joints, (working along joints can drag out too much grout) to remove grout haze from tiles and finish the joints, make sure not to press too hard on joints. As you work, check each joint is full and smoothly finished. Continue this process with other joints in remaining quadrants.

Consider caulk. For joints at the wall and flooring tiles interface it is best to use caulk instead of grout. There are benefits to using caulk along wall joints. All ceramic tiles may expand or contract depending on temperature fluctuations. The wall joints are also known as expansion joints. Using caulk here will buffer expansion and contraction a bit.

Let the floor tiles cure. Wait for the entire floor tiles design to cure for about a week before giving it a good mopping to remove remaining grout haze. You may also choose to seal the grout with a sealer to lock out dirt and or grease.