Clean the wall to remove debris and stains. Rinse the wall off with a hose, then sweep away remaining dust and debris with a concrete brush. Spray off stubborn stains with a pressure washer. Strip away any paint on the wall with a pressure washer as well. Another way to remove tough stains is by attaching a wire brush to a right-angle grinder. Use the brush to scrub off the stains.
Apply a concrete bonding agent to the cleaned wall. Dip a 3 in (7.6 cm) paintbrush into the liquid bonding agent and use it to coat the wall from top to bottom. Keep the layer as smooth as possible to ensure the veneer fits evenly on the wall. You can get bonding agents, along with any other tool you need, online or at most home improvement stores.
Combine a veneer mortar mix with water in a wheelbarrow. Prepare the mix according to the manufacturer’s instructions to get it to a firm, spreadable consistency. If you don’t wish to use a store-bought mix, try making your own instead out of masonry cement and sand. Using a pre-made mix is much simpler and faster, however.
Make your own mix by combining 1 part masonry cement with 3 parts masonry sand. Put an acrylic polymer in a separate container to mix with water according to the manufacturer’s instructions. Combine all of the ingredients in your wheelbarrow to finish the mortar.
Coat the wall with a 1⁄2 in (1.3 cm) layer of mortar. Try using a hawk to scoop the mortar out of the wheelbarrow and then transfer it to the wall with a trowel. Using both tools together makes the process much faster. Apply the stucco to the top of the wall and spread it from left to right with a single motion of the trowel. Continue doing this to add more mortar as needed to cover the wall and smooth out the layer until it appears uniform.
https://baranaceramic.com/wp-content/uploads/2019/12/Installing-Stone-Veneer-3.jpg7501150administratorhttps://baranaceramic.com/wp-content/uploads/2017/01/logo-3.pngadministrator2019-12-04 08:00:202019-12-05 02:56:39How Installing Stone Veneer?
Gather your supplies. You will need to have your peel-and-stick tiles prepared, a tile cutter or utility knife, and level. Pretty basic, huh? If you tiles are not stuck together on sheets, you may also need spacers to make sure they are all evenly spread. Clean your walls. The sticky backings of your tiles can’t adhere to walls if they are dusty or greasy.
Use a damp rag to completely wipe down walls, and then let them dry completely. Measure your space. It is important to make sure you get a good measurement so you know exactly what size you should cut your tiles. Choose a stopping point, either directly below your cabinets or at an arbitrary point on the wall.
Make sure that you have enough tiles to fill the measured space, as well as a few extras for precaution. Use a level and straight edge to mark your stopping point along the wall. Stick your tiles to the wall. Peel the backing off the tiles, and stick them to your desired location. Always start from the bottom center of the wall and work your way out.
Firmly press the tiles each time you stick them to the wall, to make sure they are firmly adhered. Hold a straight edge or level to the sides of your tile as your press, to make sure that they don’t shift out of alignment. Finish attaching tiles. Work your way across the wall, until the entirety of your desired space is filled up. Cut any pieces to fit outlet holes or edges and corners before you attach them to the wall.
Enjoy your new tile backsplash. To keep it looking its best, wipe the backsplash clean with water or a generic kitchen cleaner occasionally. Enjoy your new tile backsplash! Once you have completed all the installation steps, managing your new backsplash is easy. Wipe it down occasionally with a generic kitchen or glass cleaner to keep your backsplash looking its best.
https://baranaceramic.com/wp-content/uploads/2019/11/Peel-and-Stick-Tile-Backsplash-4.jpg7501150administratorhttps://baranaceramic.com/wp-content/uploads/2017/01/logo-3.pngadministrator2019-11-19 08:00:522019-11-20 07:54:13Applying a Peel-and-Stick Tile Backsplash
Tiles are both stylish and practical. Unfortunately, over time, they can get greasy and dirty. To do a general floor clean, mop the porcelaintiles with water and atile cleaner. If your tile splashback has greasy marks on it, use soapy water to the oil splashes. Clean the grout between your tiles with baking soda and vinegar to remove discoloration. These methods are quick and easy, and will leave your string stonetiles looking sparkling clean!
Sweep up any dust and dirt with a dustpan and brush. Use the brush to push any debris and dust into the dustpan. This avoids you spreading the dirt around the floor when you mop it later. If you don’t have a dustpan and brush, use a broom instead.
Mix water and tile cleaner in a bucket. Choose a tile cleaner that is designed for your type of tiles. For example, look for a commercial cleaner marketed as “ceramic-friendly” or “safe for stone floors.” Fill a mop bucket with water and add the tile cleaner, as directed on the back of the container.
Purchase tile cleaner from a cleaning store. Most tile cleaners require approximately 1 capful oftile cleaner per bucket of water. Avoid using citrus cleaners on stone as this can damage the tiles. Try not to use cleaners containing soap or detergent, as these can make your tile floors slippery. If you want to make your own tile cleaner, mix equal parts of vinegar and water in a bucket. This can be used on all types of tiles.
Wipe the cleaner over the calacatatiles with a mop. Dip the mop into the bucket of water and tile cleaner, and then squeeze out any excess liquid to avoid drips. Push the mop back and forth over the entire area until the calacatatiles are clean. Press the mop down firmly when cleaning any stained areas, as the tile cleaner and the pressure of the mop will help to remove the stains.
https://baranaceramic.com/wp-content/uploads/2019/06/How-to-Clean-Tiles-4.jpg6501150administratorhttps://baranaceramic.com/wp-content/uploads/2017/01/logo-3.pngadministrator2019-06-21 08:34:122019-06-18 09:53:26How to Clean Tiles?
Sweep the tile. Begin the cleaning process by sweeping the tile. Sweeping stone tile is especially important because it removes small particles, like sand, that can damage the floor. You can use any type of broom, but a dust mop is ideal because it helps the cleaning process go by faster. Do not drag furniture when moving it for cleaning the floor. Instead, have someone help you lift it and move it.
Use a mop with dish soap. The easiest way to clean your walltile is with a mop and dish soap. Use a few tablespoons (30-45 ml) of a pH-neutral dish soap instead of a harsh and acidic cleaner. Combine the cleaner with water in a bucket, and use a mop to wash down the floor until all of it has been cleaned. Seventh Generation and Method are a few brands of dish soap that you could use.
Rinse the floor. You can use the same bucket and mop you used to clean the floor, but make sure to rinse them out thoroughly. There shouldn’t be any detergent left. Fill the bucket with warm water. Use the mop to rinse the floor. Going over the tile with warm water prevents streaking caused by leftover cleaner. Rinsing the floor also helps to remove leftover sand and debris.
Dry with a towel. Drying the floor by hand is better than allowing it to air dry because air drying can cause water spots. Grab a clean towel and dry the floor by hand. It takes a while, but it gives your floor the best result.
Give the floor a shine. Complete the cleaning by giving your floors an added shine. There are several ways to do this. An easy way to do this is by using a few tablespoons (30-45 ml) of salt. Use the salt with a wet cloth and rub until the cloth is soft and dry. You can also use self-shining wax or extra virgin wax. Avoid using too much wax or you could cause your floor to appear yellow. To remove excess wax, scrub with water and neutral soap, or use a wax remover.You can use black shoe polish for black stone.
https://baranaceramic.com/wp-content/uploads/2019/05/Doing-a-General-Cleaning-Before-Clean-Stone-Tile-1.jpg6501150administratorhttps://baranaceramic.com/wp-content/uploads/2017/01/logo-3.pngadministrator2019-05-24 07:21:062019-07-30 08:57:41Doing a General Cleaning Before Clean Stone Tile
My friend asked me how to choose the tile in the living room. My requirements are very simple, wear-resistant, skid-proof, easy to take care of, bright space, and also clean and generous, it is best to make the living room have the home warm, more comfortable to use, that’s all. My God, this request is “very simple”, suddenly reminds me of “I only want colorful black”, “really simple.” There are many kinds of ceramic tile, which I do not want to count, wooden tiles, polished tiles, marble tile, glaze tiles, micro-crystalline stone, tiles, cement tiles, rustic tiles, modern rustic tiles, and so on. This is a further subdivision……Stop! Stop to divide it, let me steal a lazy.
How do you choose the living room tiles? First from the selection of tile performance. The living room is a public area, the frequency of use is relatively high, and the tiles abrasion is the primary factor. The full body polished tiles can be selected. Anti skidding is the most important thing in the home life. If the tiles in the home are not skidding and do not dare to walk in big steps every day, should be careful and threaten the health of children and the elderly. Antiskid requirements are relatively high, you can choose antique tiles, antique tile are glazed rustic tiles, excellent skid resistance. Now, when selecting tiles, skid resistance is a standard for testing whether tiles are qualified. Generally, the floor tiles have certain skid resistance.
I was still talking to my family about the robot last night. It must takes time and patience to keep the room clean and tidy. If there is an easy to handle grey tile, why don’t we choose it? You can choose wood tiles, ceramicwood tiles has the wood floor texture and color, good handle, easy to clean is famous.
The contrast tile lay out the space effect, the luxurious atmosphere style: Of course, we need to choose marble tiles. The marble tile texture is natural and delicate, the color and lustre are rich and colorful, with the noble blood of natural stone, use the simple lay out methods, it can be paved with beautiful results. Comfortable and soft style: Modern rustic tiles and polished tiles can create a comfortable and warm effect. Its glossiness is the most comfortable brightness and natural softness of human body.
Contracted style: recommended cement floor tiles, grey space without white monotonous, nor black melancholy, simple and generous, most suitable for modern people’s biochemical concept.
Literary and artistic Romance style: recommending the colorful tiles, The colorful tile is a slow feeling, unique personality, quiet and distant, romantic and charming, There are not only have simple and elegant flower lines, , but also complicated geometric patterns. No matter how dull the space is, the ornament of the colorful floor tiles will always bring you a pleasant surprise.
Some small collocations that need to be used when laying tiles. If you do not want to use the tiles in a monotonous way, add the wave line tiles. The function of beautifying the space by wave line tiles can not be underestimated. It can also play the function of dividing space. Especially with the matching of flower tiles, improve the decoration grade, enrich the space. The corner flower tile is mainly used in conjunction with the octagonal rustic tiles, so that the appearance of the tiles on the floor is more beautiful. And the star anise rustic tiles complement each other to create a perfect classical atmosphere. Skirting tile is mainly used in the corner, one is to protect the wall, the two is to give the wall and the ground an excessive effect, and the color connection is more harmonious.
Now let us talk about the size of the ceramic tiles. When decorating a room less than 40 square meters, 600*600mm tiles should be considered. If 50-60 square meters of family decoration, 600*600mm or 800*800mm tiles are available. If it is decorated in 50-60 square meters, 600*600mm or 800*800mm tiles can be used. In the decoration of 60 square meters above room, you can consider the use of 800*800mm tiles. Of course, this is not absolute. It is just a suitable suggestion. Some people like small corlor tiles lay out in the large living room, and now there are large size tiles, specifications 1200*900mm, or even 2100mm specifications.
https://baranaceramic.com/wp-content/uploads/2018/06/Choose-Tile-according-to-this-method.-One-thousand-living-rooms-are-paved-with-one-thousand-kinds-of-beauty-1.jpg600900administratorhttps://baranaceramic.com/wp-content/uploads/2017/01/logo-3.pngadministrator2018-06-04 02:55:072019-11-27 09:45:26Choose Tile according to this method. One thousand living rooms are paved with one thousand kinds of beauty