Posts

How Doing General Cleaning and Polishing?

/in /by

Wipe marble tiles surfaces with a wet cloth. Use only warm tap water, as many household cleaners are too harsh for marble tiles counters. Wipe the length of the counter with a wet cloth. Microfiber cloths are best for this if you have them, they’ll give the counter a better scrub without needing to use a household cleaner. If you need to clean your counter more thoroughly, you can use commercial cleaners specifically designed for marble tiles.


For marble tiles floors, passing a dust mop on the surface regularly should be enough for regular cleaning. However, if the floor is dirty and requires some extra cleaning, add a couple of drops of dish soap to a bucket of water and use a microfiber head mop to clean the floor with this solution. Dry the floor thoroughly after cleaning it. This kind of cleaning should be done daily to clear crumbs or any dust that may have accumulated on the counter, it won’t clean serious stains.


Wipe tiles dry with a separate cloth. Don’t let the marble tiles just air dry, since marble tiles is easily marked by water spots. Use a microfiber cloth to wipe tiles until they’re dry. Spread a baking soda mixture over the marble tiles polish it. Mix three tablespoons (44ml) of baking soda with one quart (946ml) of water. Use a shammy to spread this mixture over your marble tiles surface.


Let the mixture sit on your marble tiles for a few hours before wiping it away with a wet cloth. Sprinkle crushed chalk over your marble tiles to polish it further. For best results, you’ll want to use a box of white chalk and use a mortar and pestle to crush it into fine dust. Use a shammy to wipe the counter in circles, buffing it and bringing out the shine.


Wipe the chalk dust away with a dry cloth after buffing it. Remove the painter’s tape after applying the silicone adhesive and before it dries. Start removing each piece of tape immediately after applying your adhesive beads. Either remove your tape after each bead or all at once after applying all of the beads.

How to Clean Grout with Toilet Cleaner?

/in /by

Grime and water stains on the grout in your bathroom or your kitchen can be unsightly and hard to clean. You may struggle to clean grout in your home using conventional cleaners and be hesitant to use bleach. Instead, you may try using toilet cleaner to get rid of stains and grime on grout. You should select a toilet cleaner and then clean the grout with the cleaner properly. You should also learn how to maintain the grout in your home so it always looks its best.

Scrub the mildew with a microfiber cloth. Use a microfiber cloth to scrub in between the towels to remove the mildew. It will take some force to scrub out mildew, especially set-in mildew, so scrub the cloth hard in areas where mildew appears. Remember to wear gloves if you’re scrubbing in bleach.

Use a toothbrush for hard-to-reach places. If there is mildew built up in cracks and crevices, use a toothbrush. A toothbrush is a great tool to get into corners and cracks where mildew lingers. Make sure to check cracks where grout is found for mildew. These areas are often neglected during cleaning, which can cause mildew to spread.

Give yourself enough time. There is no secret to removing mildew other than a lot of hard work. Mildew, especially if it’s been built up over long periods of time, can sometimes be difficult to remove. Make sure to give yourself adequate time to fully remove the mildew. For grout that’s heavily infested with mildew, the job may take over an hour to complete.

Use vinegar to remove water stains. Mildew can sometimes cause water deposits to build up on the walls surrounding grout and tiles. If you notice water deposits, saturate a paper towel with white vinegar. Place the towels over the water stains and leave them on for a few hours. Then, remove the paper towels and use a cloth or cleaning brush to scrub out the stains.

How to Polish Tile Floors?

/in /by

A well-polished tile floor can make a room feel clean and inviting. Whether you have ceramic, vinyl, stone, or any other type of tile flooring, giving your tile a shiny luster doesn’t have to be difficult, time-consuming, or costly. The keys to a polished tile floor are a clean and well-buffed surface and regular maintenance.

 

Dirty and discolored grout will stand out once you’ve finished polishing the tile, so it’s best to clean it well before you clean the rest of the floor. You may need to put in a little elbow grease and get down on your knees to scrub the grout well. Treat very dirty grout before you start scrubbing. Sprinkle baking soda over the grout, then spray vinegar onto it. Leave it to sit for 5 minutes before you start scrubbing.

 

If you have a lot of grout, it’s best to use a grout brush because it will be more efficient than a toothbrush. You can buy a grout brush for a few dollars at most department stores or online. Don’t scrub the grout so hard that it starts to flake or chip off! Use a mop to clean the whole tile floor. It’s important that you clean the tile floor well before you begin to polish it. Because you’re not using chemical soap, you don’t need to mix or slosh the water to create suds.

 

Dip your mop into the vinegar solution, wring out any excess water, and mop the floor in broad strokes. Work your way from one end of the room to the other, taking care not to miss any spots on the tile floor. Don’t forget any corners, cabinets or pantries. Apply club soda to remove any built up floor wax. Club soda is an excellent natural and environmentally-friendly wax-stripping alternative.

Fill a clean bucket with only club soda and scrub your tile with a brush to remove old wax. Then use clean water to mop up any residue and allow the tile floor to fully dry. For a stubborn wax buildup, you can let the club soda sit for a few minutes before you scrub it.

how to choose floor tiles

How To Choose Floor Tiles?

/in /by

how to choose floor tiles

1, if your home space is relatively small, it is like cooking area, bathroom area, you can choose a smaller size of the tile, so that the shop will not waste more, but also to make the space looks more coordinated. The utility model can also avoid the inconvenience caused by the construction of the large-scale cutting of the ceramic tile.

2, we should also pay attention to the selection of water absorption rate, which is an important indicator of its quality. We can pour some water on the back of the tiles. If the water disappears faster, the higher the water absorption rate is, the looser the texture is and the weaker the strength is, and vice versa.