Posts

How Using Soap and Water?


Clean off any debris first. You don’t want to scrub leaves or dirt into the stone if you can help it. Sweep the area with a broom or wipe it down with a clean cloth to get it ready for scrubbing. Mix dish soap and water in a bucket. Pour in 1⁄2 cup (120 mL) or so of dish soap, then fill up the rest of the bucket with water.


Slosh it around a little to mix the soap into the water. You just need enough dish soap to make the water sudsy. Scrub the area with a scrubbing broom or brush. Dip the brush or broom into the mixture, getting it thoroughly wet. Scrub the stone in a circular motion, making sure you scrub all of the tiles thoroughly.


Dip the brush back into the mixture as it gets grimy. If you need to, wash the brush or broom out with a hose or in the sink. On stubborn areas, you can try a solution of half water, half vinegar or lemon juice. Rinse off inside areas with clean water. Once you’ve scrubbed down the whole area, dump out your bucket and fill it with clean water.


Rinse out your brush or broom, then go over the tile or counter to rinse the soap off. On a counter, you can also use a clean cloth to rinse it off. Spray outside areas with a small nozzle to get off dirt and caked-on grime. Attach a small sidewalk sweeper nozzle to the end of your hose.


Turn the hose on full blast and run the thin stream of water over your window or door features or patio tile. Rinse all the soap and dirt off until the area is completely clean. You can find these nozzles at your home improvement store. You can also use a power washer, but it can scour the stone if you’re not careful.

How to Tile a Bathroom Floor?

Lay out a single horizontal and vertical row of floor tiles across the floor along the chalk reference lines. Shift the fashion tiles, if needed, so any cuts that must be made by the wall are against the least noticeable wall. You also don’t want cut tiles at the entrance to the bathroom, so adjust the tiles so cuts are against the far wall. You can snap additional chalk reference lines, once the glazed rustic tile layout is finalized, if you wish.

Set the first tile in the far corner of the room and work towards the doorway. You won’t want to step on the newly laid Rome Stone tile before the mortar has a chance to dry. Work on laying the polished tile in small sections at a time. Mix up a small batch of thin-set mortar and spread a thin layer on the cement board with the notched trowel. Lay several pieces of tile with tile spacers to establish even grout lines. Firmly press the tile into the mortar so there are no air bubbles underneath. Set a level across the top of the cement tiles to make sure they are perfectly flat.

Cut tiles with a common marble tile cutter or wet saw, if necessary, to fit along the wall. As you work toward the walls, you may not be able to use a perfect number of tiles. You may also need to make cuts for Calacata tiles that sit around toilets and other rounded objects in the floor. Allow the thin-set to dry for at least a day. Follow the instructions recommended by the manufacturer before grouting.

Pull the bathroom tile spacers out from between the tiles before adding grout. Mix the sanded grout with water in a bucket, according to the manufacturer directions. Scoop some grout onto the file floor with a trowel. Firmly press it into the grout lines with the grout float, working in small sections at a time. Remove the excess grout from the surface of the Tundla tile before it has a chance to dry.

Fill a second bucket with water and use it to wet the large sponge with rounded corners. Wring out the sponge and then wipe over the wood tile so that you are moving at a diagonal to the grout lines. If you wipe parallel to the grout lines, you might gouge out some of the grout and leave an uneven surface. Rinse the sponge in the bucket of water and repeat until all the grout is removed from the surface of the tile. Wait at least 2 days for the grout to cure before sealing it. Sometimes its smart to leave a humidifier on during the two days you’re letting it sit, to help the grout gain in strength.

The Knowledge of Tile a Bathroom Floor

Tiling your own bathroom floor can be a satisfying and cost-effective home repair project if you get the correct materials and plan your project in advance. With a little planning, anyone can do it. Keep reading to learn to prepare the foundation, lay the tile, and grout your New Slate Tiles so it will last for many years to come. Get tiling!

Prepare the floor. Make sure the surface you’re going to wood marble tile is swept and clean of any debris, especially if you’re in the middle of more major renovations or construction. Make certain the existing wood floor is flat, solid, and well bonded to the sub-floor. The rustic floor and subfloor together should be at least 1-1/8″ thick.

Mix a batch of thin-set mortar. Follow the manufacturer directions, mixing the appropriate amount of water with the mortar in a bucket. The mortar should be thick, a similar consistency to mud, but not so thick that is doesn’t fall off a trowel. Don’t mix more thin-set than you can use within an hour, or it will begin to dry out. Spread a layer of thin-set on the sub-floor with the notched trowel. Spread the mortar quickly, but also evenly. Use firm sweeping motions with the trowel.

Cut the cement board to fit the space. If you want to reinforce the floor with cement board, score it with a utility knife before laying it over the thin-set mortar. Pound in roofing nails along the edge to secure the backer board to the floor. Continue until the floor is covered and apply a thin layer of thin-set mortar over the joints. Wait until the next day to begin laying cloud tile. In the meantime, you can prepare the reference lines to make sure the tile will be laid evenly.

Establish a straight vertical and horizontal reference line from the center of the room. If you simply start laying tile along a crooked wall, it will look really crooked by the time you reach the opposite wall, so you need to use a mason’s chalk line (a piece of string covered with chalk dust that you can snap into place) to establish easily-removable reference lines.

Identify the most visible wall when you walk into the room. This is the wall with the longest area of continuous spots tile. Determine a 90-degree angle from that wall, using a square, and snap a chalk line across the room. Use the square again to mark a perfect 90-degree angle from that chalk line and snap another chalk line that’s perpendicular to the first one. Now you have two intersecting chalk lines as a reference to lay the first tile.