Posts

What Should We Do After Finishing Your Countertop?

/in /by

Allow the mortar to set overnight. After tiling a countertop, you should let the mortar dry according to the manufacturer’s instructions. While it may be only a few hours, waiting overnight ensures that everything is well set when you get back to work.

Grout the marble tile countertop using the grout of your choice. Remove the vinyl natural marble floor tiles spacers. Then, use a rubber float to press grout into the grout lines. Work smoothly and methodically, using a rubber float to spread the grout and wipe up any excess.

Remove excess grout by holding the rubber float at a 45-degree angle and dragging it across the floor tiles in a diagonal direction.

Clean the tiles with a damp sponge when finished. Once the grout is evenly distributed in the joints, clean the grout off the room tile faces using a damp sponge. This should wipe off any residue or grit that got on the wood tiles while installing. Only swipe over the surface of the tiles — do not dig into the grout lines.

Allow the grout to dry before adding a finish to the counter. To protect your onyx tiles for years, you’ll want to apply a finishing solution to the grout. Find a grout and tile sealer that works for you at your local hardware store and apply according to the directions on the bottle.

What are the problems that need to be paid attention to in the process of tile paving?

/in /by

Do not know what is the reason, many people like to mix the ceramic tile and cement, perhaps because the ceramic tile is more expensive, but the ordinary cement tiles mortar is worried about the sticky, so the ceramic tile is added to the cement mortar and stirred in the mortar. Many people think that ceramic tile glue is almost the same as cement, so mixing it together is no problem. Actually, the ceramic tile glue has its own formula, but when the ceramic tile designs glue and cement sand mix together, the performance of the ceramic tile glue is greatly reduced. If cement mortar has better water retention and better placement, it is recommended to add cement paste to the cement.

Ceramic tiles shop can not be perfect each batch, there will always be a variety of problems, it is suggested that in the process of paving, find problems in time to remind the business of quality or color difference and other problems, timely consultation and solution. It is suggested that the owner inform the constructor before construction: if there are any problems found in the construction, we should timely feedback, so that we can deal with them in time and avoid many problems. In the process of paving, it is found that the tiles have problems, such as the size specification, the ceramic tile price and so on, and the construction should be taken out as far as possible. It can cut small pieces and splice into mosaic use.

Because of the cause of heat expansion and contraction, the ceramic floor tile does not leave the seam, it affects the service life of the tile, and does not leave the seam. The tile will squeeze each other, causing the problems of the glaze crack, the arch, the empty drum, the falling off and so on. Therefore, whether the tiles are plaster or the “seamless tiles” currently mentioned in the market, both of them need to be sewn. The specific width of the stitch should be communicated with the owner before the tile is padded. In order to be more intuitive, the owner can see how good the stitch is when it is decorated.

In the course of laying, tiles are unavoidable to be machined, and when corner paving is applied, they should also be chamfered and collaged. In the collage of Yang Jiao, be careful when chamfering, and try not to damage the glaze. It is best to let merchants or owners get a large processing plant cut. If you are in a hurry, we recommend using some portable electric cutting machines.

This problem is often ignored. When tiles are put up, everyone is careful. Once the brick is put up, many people don’t notice. So, many people stir the cement, move back and forth on the brick, and some tools pull back and forth.In particular, some processes such as paints, coatings, carpentry and so on are laid behind the tiles.Therefore, the laying of good tiles should be covered with protective film, and it is required to lay a good paste for at least 24 hours or more before walking on it.
In order to improve the effect of ceramic tile and stone placement, it is generally preferred to use beautiful sewing technology. The gap is not yellow, moldy, and easier to clean.It should be noted that the stitch should be done as soon as the ceramic tiles are dry. To prevent the ceramic tiles in kitchen from being dry, the construction on the surface of the tiles will cause the loosening of the tiles, leaving the hidden danger of hollowing out.

Glazed Tile Selection Guide

/in /by

First, to see the stability of glazed tiles.

Glazed tile according to its production process can be divided into a single firing and two firing. But according to its stability, glazed tile SINGLE-FIRED relative to the two firing for thermal stability will be better, but the process of two kinds of production have their advantages and disadvantages, therefore, consumers can also choose according to different requirements in the purchase.

Two, look at the green strength of glazed tiles.

When choosing the best choice for a well-known brand manufacturers, have the test proved that high standards to ensure brand manufacturers can be suspended load more than 100kg will not have fracture phenomenon, but some poor ordinary manufacturers are unable to bear the pressure of 50kg, some of them are still prone to cracking phenomenon. Therefore, in the purchase to see the brand awareness of manufacturers.

Three. Look at the water absorption rate of glazed tiles.

In general, the wall glazed tile in the water absorption rate is about 10-20%, manufacturers are generally around 18%, and a glazed brick firing and the water absorption rate of only 10%-13%, if some high water absorption tiles in the tiling is very dirty in the cement, agreed to absorb, it will be easy to make. The glaze and embryo surface cracking, and some shoddy bricks with a period of time behind the foot will come off. Therefore, in the purchase, we should pay particular attention to the water absorption rate glazed tile.