Often overlooked 12 small details in paving tiles

The tiles paving is stuck is not s small things it looks very simple, there seems to be no big deal in an accident, but if often happens, it will always upset people. As the saying goes, details are very important. in fact, many problems occur because some details are not well done. the marble tiles paving is the same. today, I will share with you some small details that are often overlooked in the tiles paving.

The wall should be handled well

Some walls are cracked or connected to other materials, such as cement walls and wooden boards. Before laying tiles design, the cracks in the wall should be fixed and connected with barbed wire, then reinforced with cement, and finally the tiles price should be laid, so as to avoid cracking of the ceramic wall tiles in the later stage.

Whether small tiles need to soak in water depends on the specific situation. When laying tiles with ordinary cement mortar, some ceramic tiles with relatively high water absorption are what we usually call wall tiles. they need to be soaked in water, and they must be soaked fully. However, some floor tiles with low water absorption, such as polished tiles and marble tiles design, should not soak in water whether they are pasted on the floor or on the wall. There is also a case where if bath tiles are stuck with cheap tiles glue, no matter wall tiles or floor tiles design, there is no need to soak up water.

When you need to soak water, you should also pay attention to the fact that the time for each batch of tiles to soak water is as much as possible, and the water used should be as clean as possible so as not to cause chromatic aberration after the paving is stuck.

Another point is that ceramic that need to be soaked in water should be soaked as much as possible. when they are used, they should be soaked as much as possible in advance, especially when they are spread and pasted on the back. in case there are too many bubbles and they are not used up, they cannot be returned.

Magnesium oxide and magnesium carbonate are white powder with high temperature resistance. in general, the ceramic factory’s kiln bathroom floor tiles reach over 1200 degrees at the highest temperature. at this time, the bottom of the cement tiles embryo is close to melting ( this expression may not be accurate, but the kitchen tiles embryo is soft at this moment ). in order to avoid sticking between the kitchen wall tiles embryo and the kiln’s stick, the characteristics of high temperature resistance of magnesium oxide and magnesium carbonate are used. before the outdoor tiles embryo enters the kiln, a layer of magnesium oxide slurry is brushed on the bottom of the embryo to isolate it. In this way, the sticking of kitchen floor tiles blanks and sticks in high-temperature kilns can be avoided. Therefore, sometimes we will find that there is a lot of powder at the bottom of the billet, and we must find a way to remove this white powder before paving the paving. Otherwise, cement mortar will not stick firmly to tiles, causing hollowing and falling off.

Many people think that it is a waste of time to arrange grey tiles in advance before laying marble tiles price. it is better to lay large marble tiles directly before laying buy marble tiles. In fact, BARANA personally believes that it takes some time to lay the front row tiles, but when arranging small marble tiles, some problems behind can be avoided. for example, when arranging outdoor marble tiles, you can see whether the matching waist line, flower tiles or processed tiles of the batch of tiles are matched with the main tiles. There are also obvious defects on the surface of the main white marble tiles price, whether there is color difference, whether there is large size error, etc. Before arranging tiles, the old pottery also hopes that the owner can take out each tiles to be used and explain in detail the location, quantity and special requirements of the paving paving, so as to avoid mistakes in the paving paving.

Before the paving is stuck, it is necessary to clean up the wall surface. the wall surface that has been blown with putty before needs to be shoveled off again and then pasted with mosaic tiles. otherwise, it is easy to cause hollowing and falling off. If you want to use porcelain tiles glue to lay the paving on the back, then you must level the wall.

When laying tiles with ordinary cement mortar, attention should be paid to the mixing ratio of cement and sand. the wall tiles is 1: 3, the cement floor tiles is 1: 2, and the cement label is No. 32.5 cement. If it is a ceramic floor tiles on the wall, it is suggested to use marble porcelain tiles glue or adhesive as far as possible to lay the paving, so as to avoid hollowing and falling off in the later stage.

I don’t know what the reason is. many people like to mix tiles glue with cement. perhaps it is because polished marble tile glue is more expensive, but they are worried that it won’t stick well with ordinary cement mortar, so they add polished marble tile glue to cement mortar and stir it for use. Many people think that the composition of polished floor tiles adhesive is similar to that of cement, so it is no problem to mix them together. In fact, the polished porcelain tiles adhesive has its own formula, but when it is mixed with cement sand, the various properties of the polishing tiles adhesive are greatly reduced. If the cement mortar can have better water retention and the paving is laid more conveniently, it is recommended to add the tiles glue essence to the cement.

Tiles can’t be perfect in every batch. there will always be problems like this. BARANA suggested that the master should remind the owner or the merchant in time when finding problems in the process of laying the wood tiles. in this way, before the wood marble tiles are laid down, everyone can negotiate and solve them in time instead of waiting for all the cement tiles to be laid down. then speaking of the problems, the builder and the material side will shuffle each other and it will be even more difficult to deal with them. BARANA also suggested that the owner should tell the builder before the construction: if any problems are found during the construction, they should be timely fed back, so that they can be handled in time and many problems can be avoided.

If, in the process of laying glazed tiles, it is occasionally found that small tiles have small problems, for example, if there is a little difference in size and specification and there is a missing corner of a piece, the construction master will try his best to help to select it, and use it as far as possible if the edge corner angle can be cut without affecting the overall effect.

Due to the expansion of heat and contraction of cold, if the white tiles do not leave any seams, the service life of the wall tiles will be affected. at the same time, if there are no seams, the rustic tiles will squeeze each other, causing problems such as glaze cracking, bulging, hollowing and falling off. Therefore, the BARANA suggested to leave a seam for both the tilesd tiles and the ” seamless tiles design” currently called in the market. The paving floor master must communicate with the owner before laying wood tiles price. for more direct viewing, the master can let the owner see how good the seam is when laying tiles before laying tiles.

In the process of paving, it is inevitable to cut and process the corner corners. when paving the corner corners, chamfering and collage are also necessary. when chamfering and edging the corner corners, care should be taken not to damage the glaze surface as far as possible. it is best to let the merchants or owners get the large processing factory to cut it. If you want to be on site in order to make time, it is recommended to use some portable electric cutting machines for processing.

This problem is often overlooked. when pasting tiles, everyone is careful. once the wooden tiles are laid, many people do not pay attention to it. as a result, many people stir cement on the newly laid tiles, walk back and forth, and some tools also pull back and forth. In particular, there are some processes behind the tiling, such as painting, painting, carpentry, etc. This will lead to scratches on the surface of the cement floor tiles that have already been paved, loosening of the whole, surface contamination and other problems. Therefore, it is necessary to cover and protect the ceramic rustic tiles that are paved, and require the tiles to be paved for at least 24 hours before they can move around.

In order to have a better effect after the paving is stuck, the U.S. sewing process is generally used. after the U.S. sewing, the gap is not yellow, moldy and easier to clean. However, the old pottery has to remind us that the U.S. joints will not be carried out until the tiles design are dry and solid. Avoid the hidden danger of tiles loosening and leaving hollows and falling off due to the us joint construction on the surface of the tiles.